background image

 

 

TROUBLESHOOTING 

5- Warm beer 

A- Defective pump. 
(Check motor also) 
 
B- Defective motor. 
(Check pump also) 
 
C- Refrigeration unit is not 
running. 
 
D- Conduit lines located in 
overheated area. 
 
 
E- Conduit lines flooded in 
PVC chase. 
 
 
F- Un-insulated or poorly 
insulated lines. 
 
 
 
G- Thermostat. 
 
 
H- Condenser fan motor 
not working. 
 
I- Freon leak. 
 
J- Dirty condenser. 
 
K- Condensation in conduit 
isolation. (May be caused 
from cleaning lines) 
 
 
 
 
L- Warm walk in cooler 

A- Check returns line in reservoir 
for liquid flow. Replace pump. 
 
B- Replace motor. 
 
 
C- Refer to 2 
 
 
D- Remove from any hot water 
pipes or kitchen area with stove or 
glass washer. 
 
E- Remove lines from PVC, 
thoroughly dry PVC and 
repair/replace conduit as needed. 
 
F- All lines should be fully 
insulated from cooler to 
dispenser, including glycol lines 
from power pack into cooler. 
 
G- Adjust temperature to colder 
setting. 
 
H- Replace condenser fan motor. 
 
 
I- Repair leak and recharge. 
 
J- Clean the condenser. 
 
K- Check trunk housing in areas 
for dropping or low spots. Split 
insulation approximately 5” and 
separate. Allow any water to 
drain, and then air dry. Close and 
seal trunk housing. 
 
L- Refer to 1 

Summary of Contents for CWA-2













Reviews: