Quality since
1946
4
Quality since
1946
5
Motor
3009476
Wire Assembly, Red 222"
0203600
Blue Wire
0203700
To Terminal Controlled
By Ignition Switch
Wire Assembly
To Battery
0203800
Black Wire
To Frame Or Battery
Negative Terminal
Adapter
3009863
Socket Assembly
0203200
To Truck Frame
1
2
3
4
5
6
7
8
9
10
11
12
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • buyersproducts.com
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • buyersproducts.com
Installation Instructions
TGS05B
Fig. 1 Mounting
—continued inside
3011396 Rev. A
WARRANTy
Buyers Products Co. warrants all truck/trailer hardware manufac-
tured or distributed by it, to be free from defects in material and
workmanship for a period of one year from date of shipment. Parts
must be properly installed and used under normal conditions. Any
product which has been altered, including modification, misuse,
accident or lack of maintenance will not be considered under
warranty. Normal wear is excluded. The sole responsibility of
Buyers Products Co. under this warranty is limited to repairing or
replacing any part or parts which are returned, prepaid, and are
found to be defective by Buyers Products Co. Authorization from
Buyers Products Co. must be obtained before returning any part.
No charges for transportation or labor performed on Buyers’ prod-
ucts will be allowed under this warranty.
Fig. 4
SAFETy PRECAUTIONS
WARNING
Observe the following Safety Precautions before,
during and after operating this spreader. By fol-
lowing these precautions and common sense, pos-
sible injury to persons and potential damage to
this machine may be avoided.
1. Read this entire Owners Manual before operat-
ing this spreader.
2. Read all safety decals on the spreader before
operating.
3. Verify that all personnel are clear of the
spreader spray area before starting or operating
this spreader.
4. Do not adjust, clean, lubricate or unclog material
jambs without first turning off the spreader.
5. Make sure the spreader is securely fastened to
the vehicle in accordance with this manual.
6. Do not operate a spreader that is in need of
maintenance or repairs.
7. Always disconnect the battery before removing
or replacing electrical components.
SPREADER ASSEMBLy
Check contents of box against parts list to make
sure all components are included. When ordering
replacement or spare parts refer to parts list for
part numbers.
INSTALLATION
1.
Locate and mark center of tailgate.
2.
Assemble Angles (18, 19) and Braces (20) as
shown in Fig.1 Use 3/8" carriage bolts, flat washers
and nuts. Do not tighten fasteners at this moment.
3.
Center assembly on top of tailgate. Lower angle
must be flush with top and inside surfaces of
tailgate.
4.
Position braces (20) on top of side rails. Using
holes in braces as guides mark and drill holes for
3/8" screws.
5.
Attach braces to side rails using 3/8" screws,
flat washers and nuts.
6.
Center spreader assembly on top of rear
bumper and align with holes in Angle (18).
7.
Using holes in spreader frame as guides, mark
and drill holes for 3/8" screws in rear bumper.
8.
Assemble spreader to Angle (18) and rear
bumper. Adjust position of Angles (18, 19) to bring
spreader into vertical position. Tighten all screws
at this moment.
chart a torque
1/4-20
6.0
5/16-18
11.0
3/8-16
20.0
Bolt nUt size
torqUe (ft-lBs)
Bill of Materials
1
3007683
1
Auger Weldment, TGS05
2
0208460
1
Bushing, TGS05 Auger
3
0208360
1
Shaft, TGS05 Spinner
4
3005706
1
Spinner, Poly TGS01, TGS05, TGSUVPRO
5
-
1
Washer Flat 1/2" SAE Zinc
6
3004245
1
Bushing, Bronze Oilite, 1/2" ID x 5/8 ODx1"
7 0208470B
1
Assembly, Coupling 5/8" bore
8
3003032
1
Bearing, 5/8" bore, 4 hole
9
KS301
1
Key, 3/16 x 1 Sq.
10 1420014
1
Pin, Clevis 1/4 x 2.5
11
-
1
Cotter Pin, 5/64 x 3/4
12
-
1
Screw Set, Soc. Cup Point 1/4-20 x 1/4 SS
item
part no.
qty.
description
Wiring Diagram
