Bushranger MC-PL-2 Owner'S/Operator'S Manual Download

Page: 8 / 16

＿

Idle Speed Adjustment

This Multi-cutter is equipped with non-adjustable fuel mixture carburetor. The idle speed is the only adjust-

ment for the operator.

Please see your Multi-Cutter Power Unit Owner’s/Operator’s Manual.

The cutting attachment may be rotating during idle speed adjustment. Wear the recommended

personal protective equipment and observe all safety instructions. Keep hands and body away

from the cutting attachment.
If idle speed adjustment is necessary, and after adjustment the cutting attachment rotates or the

engine stalls, stop using the Multi-cutter immediately!

Contact your local authorized BUSHRANGER Dealer for assistance and servicing.

WARNING

POTENTIAL HAZARD

・

Engine must be running to make carburetor adjustments.

・

When engine is running, attached tool and other parts are moving.

WHAT CAN HAPPEN

・

Contact with moving attached tool or other moving parts could cause serious personal injury or

death.

HOW TO AVOID THE HAZARD

・

Keep hands, feet and clothing away from attached tool and other moving parts.

・

Keep all bystanders and pets away from unit while making carburetor adjustments.

Before Operation

Chain Oil

1) Adding oil

1. Remove the oil tank cap and pour the chain oil (SAE

#10W-30) into the oil tank.

2. Once the oil has been poured into the oil tank, tighten the

oil tank cap to securely close the tank.

Oil tank cap

Oil tank

DANGER

・

Ensure that the guide bar and saw chain are installed on the pruner before verifying the

discharging rate of the chain oil. The rotator will be exposed and therefore dangerous if the

guide bar and the saw chain are not installed on the pruner.

CAUTION

・

It may take some time before the oil begins to discharge once the oil has been added to a new

product or when oil has been added to an empty tank. Do not turn the pruner on at a high speed in

such circumstances.

• When a new chain is to be used, immerse the chain in chain oil for some time prior to installing

it on the pruner, or pour the oil directly on to the chain and the guide bar, after installing it on the

pruner. If they are not properly lubricated with oil the pruner may seize.

Summary of Contents for MC-PL-2

















Search results

Summary of Contents for MC-PL-2

Reviews:

Related manuals for MC-PL-2

Brands by name

Popular brands

Bushranger MC-PL-2, Owner'S/Operator'S Manual

Search results

Summary of Contents for MC-PL-2

Reviews:

Related manuals for MC-PL-2

Brands by name

Popular brands