background image

5

6

    *  Do not expose discs to direct sunlight or high 
        temperatures, high humidity or dusty places. 
4. Cleaning a disc
    *  Should the disc become soiled, wipe off dust, 
        dirt and fingerprints with a soft cloth.
    *  The disc should be cleaned from the center to the edge.
    *  Never use benzene, thinners, record cleaner fluid or anti static spray.
    *  Be sure to close the CD door so the lens is not contaminated by dust.
    *  Do not touch the lens.

OPERATING THE UNIT

When you first plug the unit into the AC outlet, then press the power switch on the bottom of 
the unit, the unit will be in standby mode, the black light of standby is red. You can now press 
the STANDBY/ON button on the unit or on the remote control to switch the unit ON. The black 
light of the multi function display will light on blue.
Pull the AC plug out of the wall socket if you want to switch off completely.

POWER/STANDBY

1. Press the STANDBY/ON button on the unit or on the remote control to switch the unit on.
2. Select the sound source (CD, USB, CARD, BT, AUX or TUNER) by pressing the MODE button. 
    The corresponding display will light up.
3. Adjust the volume with the VOLUME (+ or -) button on the unit or VOLUME (+ or -) button on 
    the remote control.
4. Press the STANDBY/ON button again to turn off the unit.

Note:

1. If there is no signal under the CD/USB DEVICES/ SD CARD mode, the main unit will be 
    switched off within 15 minutes automatically.
2. During in standby mode, press any button/key can make the display light for 10 seconds.
3. Please turn the main switch off to save energy, when you do not use the unit.

CLOCK SETTING

During in the STANDBY mode.
1. Press and hold the MEMORY button until the time displays will change to 12-hour(or 24-hour) 
    digit and flash.
2. Press the SKIP/TUNE SEARCH(UP or DOWN) button to adjust 12-hour or 24-hour digit.
3. Press the MEMORY button again, the HOUR digit will flash on the display, press the 
    SKIP/TUNE SEARCH (UP or DOWN) button to adjust HOUR digit.
4. Press the MEMORY button once more, the MINUTE digit will flash on the display, press the 
    SKIP/TUNE SEARCH (UP or DOWN) button to adjust MINUTE digit.
5. Press the MEMORY button again to confirm the time.
6. Each enable state as shown above will be cleared if the key is not pushed in10 seconds.

TIMER SETTING(on the remote control)

During in the STANDBY OFF/ON mode.
1. After adjusting clock, press the TIMER button for a few seconds, "     ON" and "00:00" appears 
    on the display and the HOUR digit flashes.
2. Press the SKIP/TUNE SEARCH(UP or DOWN) button to adjust it.
3. Press the TIMER button again, the MINUTE digit will start flashing, adjust it by pressing the 
    SKIP/TUNE SEARCH (UP or DOWN) button.
4. Press the TIMER button once more to confirm and order TIMER ON time.
5. After adjusting "TIMER ON", "     OFF" appears on the display and the HOUR digit flashes.
6. Repeat the above steps 2 to 3, and then press the TIMER button once more to confirm and 
    order TIMER OFF time.
7. Now the "TUNER" appears on the display with flashing, adjust “TUNER, CD, USB, CARD “ by 
    pressing the SKIP/TUNE SEARCH(UP or DOWN) button.
8. Press the TIMER button again, the timer "VOL-13” indicator appears on the display and flashes, 
    adjust the timer volume high or low by pressing the SKIP/TUNE SEARCH(UP or DOWN) button.
9. Each enable state as shown above will be cleared if the button is not pushed in 10 seconds.
10. After adjusting "TIMER ON" and "TIMER OFF", press the TIMER button, "     " appears on the 
      display.
11. The unit will be switched on automatically at "TIMER ON" order and start playing, the unit will 
      be switched off automatically at "TIMER OFF" order.

Note:

 If the display shows "ERROR" while you set the “TIMER ON”, it means both “TIMER ON” 

and “TIMER OFF” is the same. In this case, please go to “TIMER OFF” to set the off time first.

EQ CONTROL(on the remote control)

EQ shows the present sound tone. When you press the EQ button , the sound tone changes 
as below:

TO SET SLEEP FUNCTION(on the remote control)

1. If you want to fall asleep to music, press the SLEEP button .
2. You may select the TUNER, CD/MP3, USB, CARD, BT or AUX mode in sleep function to play 
    from 90, 80, 70 up to10 minutes of music before shutting itself off automatically.

MODE SELECT

The function is that when it presses the MODE button the mode is changed. Display changes 
as below:

NE-8270 Manual.pdf   4   2015/6/10   14:04:58

Summary of Contents for NE-8270









Reviews: