20
For any help concerning set up and use of your TV please call the Customer Helpline: 0845 604 0105
•
The transmission speed differs depending on the
distance and number of obstructions between the
transmission products, the configuration of these
products, the radio wave conditions, the line traffic,
and the products that you use. The transmission
may also be cut off or get disconnected depending
on the radio wave conditions DECT phones, or any
other WiFi 11b appliances. The standard values of
the transmission speed are the theoretical maximum
values for the wireless standards. They are not the
actual speeds of data transmission.
•
The location where the transmission is most effective
differs depending on the usage environment.
• The Wireless LAN adaptor should be connected directly
to the TV’s USB port. USB hubs are not supported.
• The Wireless LAN adaptor supports 802.11 a,b,g &
n type modems. It is highly recommended that you
should use IEEE 802.11n communication protocol in
order to avoid any possible problems while watching
videos.
•
Use the other usb input, if you experience problems
with audio/video performance.
• You must change your modem’s SSID when there
are any other modems around with the same SSID.
Configuring Network Settings
Your TV’s Network Settings include Wired and Wireless
Connection options.If you try to connect Wireless
Connection when your TV does not have a USB Wi-Fi
dongle, a warning screen will appear and the TV will not
get an IP address. Try connecting the LAN cable after
this and then the TV will be able to get an IP address.
Configuring Wired Device Settings
If you are connecting the TV via ETHERNET INPUT,
select Network Type as
Wired Device
to configure.
Network Type
Network type can be selected as
Wired
or
Wireless
device, in accordance with the active connection to the
TV set. Select this as Wired if you have connected to the
TV an ethernet cable. Select as Wireless if you connect
via the wireless USB dongle.
Configuration Status
This section displays the status of the connection.
IP Address
If an active connection is available, the IP address will
be displayed on this section. If you want to configure IP
address preferences, press
GREEN
button and switch
to the advanced mode.
Configuring Wired Network Settings in
Advanced Mode
While in Advanced Mode, press
RED
button to edit
settings. When finished, press
OK
to save, Press
RETURN
/
BACK
to cancel.
IMPORTANT
: The “Veezy 200” USB dongle is required
to use wireless network features.
The Wi-Fi feature can be used for a wireless network
connection. If you have the Veezy 200 Wifi Dongle
(included), select
Network Type
as
Wireless Device
to start the connection process.
To enable the Wi-Fi features, profiles should be configured
properly. Please plug in the Wi-Fi dongle (included) to one
of the USB ports.
Press the
YELLOW
button to scan for wireless networks.
Afterwards, the available network list will be displayed.
Please select your desired network from the list.
If the selected network is protected with a password,
please enter the correct key by using the virtual
keyboard. You can use this keyboard via
navigation
buttons
and
OK
button on the remote control.
Wait until the IP address is shown on the screen.
This means that the connection is now established. To
disconnect from a wireless network, you should highlight
Configuration Status
and press
OK
.
You can navigate between menu tabs by pressing left/
right buttons. The help bar on the bottom of the dialog
shows features that you may use. Press
BLUE
button
to check your internet connection speed.
You can check the signal strength by using the network
settings menu for the wireless device mode.
Information
Configuration Status
: Displays wi-fi status as
connected or not connected.
IP Address
: Displays the current IP address.
Network Name
: Connected networks’ name will be
displayed.
Press
GREEN
button to switch to advanced mode and
then press the
OK
button to edit settings.
Delete Saved Wifi Profiles
Saved profiles will be deleted if you press the red button
whilst the wireless device selection osd is on the screen.
Connecting to your Cell Phone via WiFi
(Optional)
•
If your cell phone has a WiFi feature, you can connect
your cell phone to your TV by using a WiFi connection
via a router, in order to play content from your phone.
For this, your cell phone must have appropriate sharing
software.
General TV Operation