OPERATION
OPERA
TION
ZTR 12/20
Operation Section 4-1
© 2020 Alamo Group Inc.
If you are unfamiliar with the oper-
ation of a Zero Turn Mower, READ
the Safety Section and the Controls Section before
Operating.
Training
Zero Turn Mowers are more maneuverable than conven-
tional riding mowers because of the unique steering ca-
pabilities.
Before attempting to operate this Zero Turn Mower under
it’s own power, the Operation Section should be reviewed
entirely.
After reviewing the Operation Section, board the Zero
Turn Mower
(Always from the left side or front only,
never from the right hand side
)
. Begin slowly by prac-
ticing on a smooth, hard, level surface such as concrete
or asphalt before moving to turf.
Choose an area where no people, vehicles or other ob-
stacles are present.
Do not move the Steering Levers too aggressively to the
most forward or rearward positions during your initial op-
eration. Moving to turf before being completely comfort-
able with the maneuverability of this Zero Turn Mower
could cause turf damage.
Before Starting
1.Read the
Safety
and
Controls
sections before starting
the
Zero Turn Mower.
2.Do a maintenance check before starting. See Mainte-
nance Schedule in the
Maintenance
Section.
3.Check Fuel for a sufficient amount to perform the task
at hand.
4.Adjust the Operators Seat to desired position
(See Seat
Adjustment Controls
).
5. Raise the Zero Turn mower deck to the transport posi-
tion (highest cutting setting). (
See Cutting Height
Controls).
6.The following Control settings must be applied before
the engine will start.
• PTO Control Switch must be down (Off position).
• Parking Brake must be set (Up position).
• Both Steering control Levers must be in the Neutral
Lock position.
• Operator must be in the seat.
Starting the Engine
1.
Operator sitting in seat.
NOTE; The Seat is
equipped with an operator presence switch and the
unit will not start if operator is not sitting in the seat!
2. Raise the Zero Turn mower deck to the transport po-
sition (highest cutting setting).
3. The PTO Switch must be disengage.
4. Engage the Parking Brake.
5. Steering Levers in the Neutral Lock position.
6. Move Throttle Control to middle position.
7.
Pull Choke Up. (On cold starts)
8. Enter Console Un-Lock Code.
9. Press Start/Stop Button after the Green light is on.
If the engine fails to start after 5 seconds release the
Starter Button wait 10 seconds and retry.
10. When engine starts release Starter Button and push
the Choke Knob down.
NOTE:
When engine is running, engine RPM shows
in the LED Display. When engine is shut down total
usage Hours displayed.
11. Allow the engine to run at a moderate speed for a
short time before beginning to mow.
Shutting Down the Engine
The Engine can be shut down at any
time by simply pushing the
Start/Stop Button, however this should not be done with
Zero Turn mower deck engaged and forward or reverse
travel in progress. This should be done only in as emer-
gency procedures.
NOTE: The engine will shut down during operation
if the operator leaves the seat.
Proper Shutdown is achieved as follows:
1. Disengage the Zero Turn Mower deck by pushing the
PTO Switch down.
2. Bring the engine down to idle speed.
2. Place the Steering Levers in the Neutral Lock position.
3. Set the Parking Brake.
4. Depress the Start/Stop switch.
Summary of Contents for HDZ-4 Series
