![background image](http://html1.mh-extra.com/html/bush-hog/hdc-2-series/hdc-2-series_operators-manual_2834800051.webp)
CONTROLS
CONTROLS
HDC2 ZT 04/18
Controls Section 3-5
© 2018 Alamo Group Inc.
PTO Switch
The PTO Switch is located on the Console and is Yellow
in color.
To engage the Zero Turn mower blades pull the PTO
Switch switch up and to disengage push the switch down.
NOTE: The PTO Switch should only be engaged when
the engine is running and the steering levers are in
the Neutral position. The Zero Turn Mower will not
start if the PTO Switch is pulled up prior to starting
the Zero Turn Mower. It must always be in the OFF
(Down) position to start.
The Fuel Tank is located under the operators seat and
the Filler Neck is located on the left hand side toward the
rear of the seat. The Fuel Cap is tethered to the tank to
avoid dropping when refueling the Zero Turn Mower.
Gasoline is highly flammable. The en-
gine and exhaust system become
very hot during operation.
Allow engine and exhaust system to cool down before re-
fueling the Zero Turn Mower.
Use CAUTION and only fill outdoors.
Fill to the bottom of the filler neck (DO NOT OVER FILL).
Do not fuel the Zero Turn Mower near an open flame.
Clean away any spilled fuel after re-fueling and before
re-starting the Zero Turn Mower.
Check the gas fill cap often for damage to gasket. If dam-
aged replace the fill cap.
The engine is designed to operate on 87 Octane un-
leaded gasoline.
Damage to the engine may occur if E85 Alcohol based
fuel or Methanol fuel is used.
The Cutting Height is controlled by the Height Control
Knob. Push the Foot Control Pedal all the way forward
to lock the deck in the lockout position. Adjust the Height
Control Knob to the desired cutting height by aligning the
indicator point on the panel. To position the deck at the
set cutting height, push the Foot Control Pedal forward
while pulling back on the Transport Locking Lever and
slowly let pressure off the Foot Control Pedal allowing the
deck to drop to the set cutting height.
PTO
Switch
Cutting Height Controls
Fuel Tank and Filler Neck
IMPORTANT:
To maintain an even cutting
height, all tires must have equal air pressure
of 15 psi /103kPa / 1bar.
Filler
Neck
&
Fuel
Cap
!
WARNING!
IMPORTANT:
Always disengage the blades
and raise the Zero Turn Mower Deck to the
highest position and engage the Transport
Locking Lever before transporting.
Height Adjustment Knob
Foot Control Pedal
Transport Locking Lever
Summary of Contents for HDC-2 Series
