BUSCH COBRA NF 0750 A Instruction Manual Download Page 37

Page: 37 / 44

Spare Parts | 11

Instruction Manual COBRA NF 0750 A - NF 0950 A WCV_EN_en

37 | 44

Spare Parts

WARNING

Use of non-Busch genuine spare parts.
Risk of fire!

●

Use only Busch genuine spare parts approved by Busch and suitable for oxygen applications.

NOTICE

Use of non-Busch genuine spare parts.
Risk of premature failure!
Loss of efficiency!

●

The exclusive use of Busch genuine spare parts and consumables is recommended for the correct
functioning of the machine and to validate the warranty.

There are no standard spare parts kits available for this product.
If you require Busch genuine parts:

●

Contact your Busch representative.

Spare parts available

Spare part

Description

Part no.

Inlet filter cartridge

Inlet filter cartridge,

paper

0532 000 006

Inlet filter cartridge

Inlet filter cartridge,

polyester

0532 121 865

Inlet screen

0534 565 893

Transparent inlet cover

Cover for inlet flange

0710 222 659

Spare parts available for Oxygen version

Spare part

Description

Part no.

Inlet filter cartridge for oxy-
gen > 21% vol.

Inlet filter cartridge,

polyester

0532 121 865

Summary of Contents for COBRA NF 0750 A













































Search results

Summary of Contents for COBRA NF 0750 A

Reviews:

Related manuals for COBRA NF 0750 A

Brands by name

Popular brands

BUSCH COBRA NF 0750 A, Instruction Manual

Search results

Summary of Contents for COBRA NF 0750 A

Reviews:

Related manuals for COBRA NF 0750 A

Brands by name

Popular brands