GETTING STARTED.
Please note that all Keyguard safes
are supplied without a preset code. To
open the Keyguard for the first time
replicate the following steps:
SETTING YOUR OWN CODE.
1. Decide upon your new personal
code, please be aware that you may
only use each number and / or letter
once. (It is suggested that you select a
4-8 digit.
2. Figure for your new code. It is very
important that you remember this
combination.)
2.
With the door of your Keygaurd XL
still in an open position turn the handle
in an anti-clockwise direction. The
locking bolt will extend and the door will
now be locked.
3.
Input each digit of your personal code,
one figure at a time. It does not matter
which order you punch in your numbers
and / or letters.
NORMAL KEYGUARD USE.
Your Keyguard XL can now be
operated using the techniques you
have learnt so far. The following
points should help clarify any final
uncertainties.
1.
During any operation of the
Keyguard XL always begin by
depressing the ‘Clear’ button.
2.
To open first input your personal
code and then turn the handle in a
clockwise direction. The door will now
pull open towards you.
3.
To close your Keyguard XL push
the door to and then turn the handle in
an anti-clockwise direction. NB.
Please turn the handle fully at least
twice to ensure it is fully locked. Check
this by turning the handle in a
clockwise direction to make sure it will
not open.
CHANGING YOUR CODE.
You may wish at some stage to alter
the personal code you have set. You
can change your code by following the
steps below.
1.
In the usual manner open your
Keyguard XL.
2.
To change the code you will need a
small flat-headed screwdriver.
3.
Undo the screw that holds the
numbered plastic plate in place, then
remove the plate.
Instructions
3.
Start by opening the Keyguard XL.
4.
Leaving the door in the open position
now turn the handle in an anti-clockwise
direction so that the locking bolt
extends
fully into the locked position.
Turn the
handle several times to ensure
it is fully
locked.
5.
Unscrew the small screw that holds
the numbered plastic plate in position.
Now remove the plate from the facia.
6.
Using the screwdriver turn the disk
that represents the first number or letter
in your code 180° so that the arrow now
points downward. Repeat this step for
each number and / or letter in your
code.
7.
Re-secure
the plate
in position with
the small
screw.
DO NOT CLOSE THE DOOR
YET
!
CHECKING YOUR CODE.
1.
With the Keyguard door in the
open
position slide the Clear button
downwards and then release it.
4. Once you have depressed the
buttons for each number in your code
the handle should rotate in a clockwise
direction and the locking bolt will
withdraw.
N.B. If any of the numbered buttons
fail to depress after you have set your
code then please ensure that they
have been turned fully 180
°
.
5. Re-check that your code works two
or three more times. If these tests are
successful you can now close the door
and safely lock it.
1.
Start with your Keyguard XL in the
upright position as pictured above. Now
slide the 'Clear' button (This is the
ridged
black button in between the two
rows of
buttons) down. Release the
Clear button
so that it can return to its
normal position.
2.
Turn the handle in a clockwise
direction, the door on your Keyguard XL
will open.
SET
NOT SET
4. Again note the arrows displayed on
the slotted disks. Using the screwdriver
return any of the disks used in the original
code to their upright and neutral position.
5. Now carefully repeat all of the steps in
the sections marked ‘Setting your own
code’ and ‘Checking your code’.
