Burkert TopControl Basic 8694 REV.2 Quick Start Manual Download Page 31

Page: 31 / 34

Accessories

ACCESSORIES

Designation

Order no.

Special wrench

665702

Wrench for opening or closing the trans

parent cap

674077

Connection cable M12 x 1, 8-pole

919061

Communication software Bürkert

Communicator

Information at

www.burkert.com

USB-büS interface set:
USB-büS interface set 2 (büS stick + 0.7 m

cable with M12 plug)

772551

büS adapter for büS service interface

(M12 on büS service interface Micro-USB)

773254

büS cable extension (M12 pin to M12

socket), length 1 m

772404

büS cable extension (M12 pin to M12

socket), length 3 m

772405

büS cable extension (M12 pin to M12

socket), length 5 m

772406

büS cable extension (M12 pin to M12

socket), length 10 m

772407

Tab. 20: Accessories

13.1

Communications software

The PC operating program “Communicator” is designed for com

munication with the devices from the Bürkert positioner family.

A detailed description and precise schedule of the procedure

for the installation and operation of the software can be found

in the associated documentation.

Download the software at:

www.burkert.com

english

Type 8694 REV. 2

Summary of Contents for TopControl Basic 8694 REV.2



































Search results

Summary of Contents for TopControl Basic 8694 REV.2

Reviews:

Related manuals for TopControl Basic 8694 REV.2

Brands by name

Popular brands

Burkert TopControl Basic 8694 REV.2, Quick Start Manual

Search results

Summary of Contents for TopControl Basic 8694 REV.2

Reviews:

Related manuals for TopControl Basic 8694 REV.2

Brands by name

Popular brands