Electronic lock system
Misprints, typographical errors and technical changes reserved.
7100
6
Befor
e fixing the outer knob, please consider whether you wish to us
e the attached
cover panel for the pr
ofile cylinder section. If so,
remove the pr
otective sheet and fix
the cover panel onto the lock section.
7
Move the outer knob into the re
q
uired position on the shaft and
fix
it
with a clearance of at least 1 mm from the
fi
tting using the setscrew.
8
A function test should be performed with an open door.
C.
Programming / function / operation
Registration of keypads with the cylinder is performed either through the keypad itself
or by the secuENTRY softwar
e. For a cylinder to be cont
rolled via a keypad, the two
units must paired. To pair a keypad to the cylinder, proceed as follows:
Registration via keypad
• Activate the keypad using the key
• Then press
FUNC
, “Menu / Code change” is displayed
• Now you can use the keys 1 or 2 to scroll until reaching the “Administrator” menu
•
Confirm with
• Now you can use the keys 1 or 2 to scroll until reaching the administrator
“Setup” menu
•
Confirm with
• Enter the administrator code of the unit to be registered
• “Data has been saved” is displayed after a successful registration
Attention! Make sure that no other powered secuENTRY unit is placed within
a close proximity when registering a new keypad or a new cylinder, as such
unit could be mistakenly paired instead of the intended one. When in doubt,
disconnect such units from power before the registration (remove batteries).
Registration using the secuENTRY software
Please proceed according to the user manual for the corresponding software.
Opening
The secuENTRY 7100 pr
o can be operated, depending on the equipment configuration,
using a 6 digit numerical code, the BURG-WÄCHTER KeyApp, or with fingerprints.
Opening with PIN code
• Activate the keypad using the key
•
Enter the 6 digit PIN code (factory-set to “1-2-3-4-5-6”).
The display indicates “Please use rotary knob!”and the LED
integrated in the cylinder flashes once when opening is successf
ul
• Rotate the cylinder knob
Opening with fingerprint
• Activate the keypad using the key
• Move the register
ed finger f
rom the top to the bottom centrally over the sensor.
The display indicates “Please use rotary knob!”and the LED integrated in the cylinder
flashes once when opening is successful
• Rotate the cylinder knob
Introduction
Congratulations on pur
chasing this BURG-WÄCHTER quality p
roduct! Thank you very
much for purchasing the secuENTRY 7100 pro electronic lock system manufactured by
BURG-WÄCHTER. This system has been developed and manufactured using the latest
technology and achieves high security standards. The electronic cylinder can be installed
easily without any drilling or installation of cables Full stop
here. Suitable for any door
prepared for pr
ofile cylinder up to a door thickness of 118
mm (59
/
59
mm, measured
at the central detent bolt). The electr
onic cylinder is perfectly suitable for both new
installations and upgrades.
Contents of this user manual
A
General
E Battery replacement
B Mounting
F
Emergency key
C Programming / function / operation
G Warranty / environment
D Technical data
A.
General
Please read the entire user manual throughly before you start the installation and
programming. Keep it in a safe place. We hope you en
j
oy your new locking system.
The secuENTRY 7100 pro cylinder can be used with the following opening media:
• Keypad P
INCO
DE
• Keypad
FING
ERPR
I
NT
• Smartdevice / App
The opening media can be obtained separately.
Administrator code / QR code
Each secuENTRY 7100 pro cylinder is provided with a QR code, which is intended both
for registration of a keypad and for integration of a locking system by means of the
optional secuENTRY software.
Without an appropriate keypad, opening media
(users) can only be registered with the cylinder by means of the optional
software. The administrator code is also indicated on the QR code label.
SN:
10 : 2D : 00 : 3E
30 : 42 : 25 : 00 : 00 : 60
12345 6
E1 : 25 : F3 : E2 : DB : 86 : C0 : 70 :
F7 : EA : 04 : 93 : 17 : 2E : BF : 9E
MAC:
AES:
ADM:
1
1
Cylinder
(SN; MAC; AES; ADM)
Attention! In case you lose your administrator code and / or your QR code, any
reprogramming and use of administrator functions becomes impossible. Please
store them carefully!
Our hint: The QR code can also be stored in an electronic form
Please note that for security reasons, the factory-set administrator code must be changed
to a custom code
as a scanned file
or a photograph on a protected data carrier.
The manufacturer assumes no liability for any injury or damage which may
occur during the assembly or due to inappropriate handling.
B.
Mounting
The installation of the secuENTRY 7100 pro cylinder is described below. Please read these
installation instructions carefully before the assembly.
The cylinder is provided with a special detent system offering you a possibility to use
the cylinder for doors up to a thickness of 118
mm (59
/
59
mm, measured at the central
detent bolt). No prior adjustment is necessary
.
Outer side / outer knob
Inner side / inner knob
Diagram of the cylinder
Cover panel
Adapter 2
Detent bolt
Adapter 1
Setscrew for
fix
ing on the on
the shaft
Remark
The base size of the cylinder is 30 mm per side. When delivered, the cylinder is
completely collapsed (the smallest door thickness). Befor
e you insert the cylinder
into the door
, you should adjust it to your door thickness.
Loosening and tightening of the outer and inner knobs is done by means of an
integrated setscrew in the knob.
Attention: Never pull the inner knob completely from the shaft, as this will lead
to damaging of the electronics! The setscrew securing the detent on the shaft
may be loosened only lightly and it always remains in the plastic knob. The
setscrew is intended as protection against pulling it beyond the shaft.
Proceed carefully during installation. Be certain to avoid shocks or abrupt actions.
The lock should not be greased or oiled.
When installing the cylinder, proceed as follows:
1
Take a rough measur
ement of the door thickness (incl. fittings).
2
Pull the outer knob from the shaft, move the inner knob over the detent system
(spacing 2.85
mm) to the
r
equir
ed dimension.
Inner knob
Adjustment range 30 mm
Diagram of the inner knob
3
Depending on the door thickness, you can af
fix
an appropriate adapter on the
outer side, in order to improve the path for the emergency key.
The following combinations are possible:
Space detent bolt /
fi
tting
(
mm
)
on the outer side
Adapter 1
Adapter 2
<
4
3
–
–
X: selection
–: not provided
44
– 53
X
–
5
4
–
6
0
X
X
Tab. 1: Space detent bolt /
fi
tting [mm] on the outer side and the required adapter.
2,
9
× 1
6
Adapter 2
M2 × 10
Adapter 1
Illustration of
adapter
fi
tting
4
I
nsert the secuENTRY 7100 pro cylinder from the outside of the door to the
inside through the mortise lock in the door and then tighten the detent bolt.
5
Push the inner knob over the shaft until attaining the re
q
uired dimension.
Please make sure that the clearance between the rotary knob and the door
fi
tting is at least 1 mm. Then
fix
the rotary knob using the setscrew.
Opening with BURG-WÄCHTER KeyApp
• Hold your smart device in front of the cylinder knob and press the opening
key of the KeyApp.
•
The LED integrated in the cylinder flashes once when opening is
successful.
• Rotate the cylinder knob.
You can download the BURG-WÄCHTER KeyApp from the App Store or the Google Play
Store
. For t
his purpose, simply enter the search item “secuENTRY” or “KeyApp”.
Compatible with Samsung Galaxy S4, S4 mini, S5 and S5 mini f
rom Andr
oid 4.3 KitKat
or 5.0 Lollipop, Apple iPhone 4S, 5, 5S, 6, 6S f
r
om IOS 8.1.3.
Please check under:
www.burg.biz/secuentry/description
whether additional
smartphones are compatible with the App.
D.
Technical data
Number of user codes
ma
x
. 2000
Mechanical emergency opening
Blocking times
After 3
x
wrong code is entered 1 minute,
then always 3 minutes
Power supply
2
x
MIGNON
LR
6
ALK
ALI
NE
Date / time
Calendar
*
Timer
*
Permanent timer
*
Hotel function / guest code
*
Hotel function / transponder
*
Time limited code
*
Smart Device / KeyApp
*
Smart Device / KeylessEntry
*
Apple Watch / KeyApp
*
Number for history
*
2000
*
F
unctions with the optional secuENTRY software only
Additional functions using the optional secuENTRY software, for example:
• User administration
• Timer and calendar functions
• Assignment of authorizations
Optical signalling
Optical signalling in the form of a LED is incorporated in the
knob on the outer
side of the door. This LED informs you on the following:
• 1 × brief: cylinder coupled
• 2 × brief: cylinder uncoupled
• 1 × brief, 1 × long, 2 sec. pause, repeating: lock in programming mode
• 5 × brief, 2 sec. pause, repeating in 20 sec.: battery in cylinder empty
E.
Battery replacement
1
Using the attached hex ke
y, loose the top setscrew on the cylinder cover
. It can be
turned out only up to the opening of the cover and will not fall out.
2
Snap the cover open.
3
Replace the batteries. Make sure the batteries are inserted with a correct polarity,
indicated at the marked point on the housing. Replace the cover.
F.
Emergency key
Using the mechanical key, you can gain access in case of failure of the system.
1
Swing the emergency key open and then insert it into the indicted
slot in the cover panel.
2
Tur
n the key 90
° clockwise. If
r
equir
ed, move the outer knob slightly to the
right and left in order to release the mechanism.
3
Turn the outer knob. The lock opens when fully turned.
Turn the key to its initial position and take it out. To close the emergency lock,
the knob should be turned twice fully in both directions.
G.
Warranty / environment
Warranty
In o
rder to be able to provide you with r
eliable high quality p
roducts and optimal
support when you need servicing or repair, we need you to present faulty or defective
devices to your vendor together with a valid administrator cod
e and the QR code(s),
with the original purchase document attached.
When you return a device component based on your right of withdrawal from the
purchase agr
eement, such component shall be adjusted to factory settings an
d the
seal on the cylinder and on the knob shall be intact. In case o
f non-compliance with
this, the warranty becomes invalid.
Disposal of device
Dear customer,
please help us avoid unnecessary waste. Should you intend to dispose of this device
at any time, please remember that many components of this device contain valuable
materials, which can be recycled.
Please be aware that electrical and electronic e
q
uipment and
batteries shall not be disposed of as household waste, but rather
collected separately. Please obtain information on the collecting
points for batteries and electrical waste from the responsible
authority of you municipality.
About interference from Bluetooth devices
Bluetooth devices use the same fr
equency band (2.4GHz) as
W
iFi devices. This can cause
interference leading to errors or even to communication failur
e. In such case, any devices
not r
equi
red should be kept disconnected from power.
Montage- und Bedienungsanleitung
Assembly and User Manual
Download: www.burg.biz
Download: www.burg.biz
Download: www.burg.biz
Descarga: www.burg.biz
Download: www.burg.biz
Download: www.burg.biz
Download: www.burg.biz
Download: www.burg.biz
Ladattava tiedosto: www.burg.biz
λήψη: www.burg.biz
İndir: www.burg.biz
Descărcare: www.burg.biz
Pobieranie pliku: www.burg.biz
Stáhnout: www.burg.biz
Letölthető: www.burg.biz
Download: www.burg.biz
Download: www.burg.biz
Download: www.burg.biz
загрузка: www.burg.biz
Download (зареди):
www.burg.biz
Download: www.burg.biz
BURG-WÄCHTER KG
Altenhofer Weg 15
•
58300 Wetter
•
Germany
[email protected] · www.burg.biz
BW_pro 7100 Zylinder_BA_sE_010100 hbg/eba 11/2017
BURG-WÄCHTER KG hereby declares that this device complies with Directive
2014/53/EU, (RED) 2014/30/EU, (EMC) and 2011/65/EU (RoHS). The full text
of the EU Declaration of Conformity can be found on the following website
www.burg.biz
Transmitting power and frequency range:
Bluetooth Low Energy
Maximum Transmit Output Power 7,5dBm
Frequency usage range 2,402GHz … 2,483 GHz
