Page 17
MUST GRIND INTO
FUNNEL FIRST
(COFFEE NAME)
SETUP COMPLETE
BEGIN SETUP OF
(COFFEE NAME)
QUIT SETUP?
YES
USE LEFT SIDE
ONLY
INSERT FUNNEL
WITH NEW NAME
REVIEW RECIPES?
NO YES
(COFFEE NAME)
NO YES
3 BATCHES DONE?
NO YES
SET NEW RECIPE?
NO YES
2 SEC.
CYCLES THROUGH
THREE SCREENS
2 SEC.
FUNNEL
CONTAINS NAME
FUNNEL CONTAINS
NO NAME
SETUP BREW VOLUMES, BYPASS,
PULSE BREW, PREINFUSION, DRIPOUT TIME
SEE SEPARATE DIAGRAMS
FOR SETUP INSTRUCTIONS
FUNNEL DETECTED
P2299
SET NEW RECIPE
Using a Smart Funnel and a G9-2T DBC or MHG
Grinder:
This function allows the operator to set
BREW
VOLUMES, BYPASS PERCENTAGES, PULSE BREW
TIMES,
and
DRIP-OUT TIMES
for each coffee name
preset in the grinder's memory.
Certain coffee
NAMES
are stored in the G9-2T
DBC's memory. When a particular name of coffee is
ground into the Smart Funnel, that name and the batch
size selected are transferred from the grinder to the
programming
chip
located in the funnel handle. The
funnel is then inserted into the brewer's left side funnel
rails. The sensor coil on the brewer reads the informa-
tion contained in the handle. The name of the coffee
flavor will then appear on the display. This then allows
the operator to set the
BREW VOLUMES, BYPASS
PERCENTAGES, PULSE BREW TIMES,
and
DRIP-OUT
TIMES
for that particular coffee
NAME
. It also allows
the operator to set other brewing parameters, such
as
BREW TEMPERATURE, READY TEMPERATURE,
BREW LOCKOUTS,
etc. Each coffee
NAME
can be set
individually to provide optimum brewing quality.
PROGRAMMING THE BREWER (cont.)
29877-3 062005
Procedure for Setting the Recipe:
NOTE:
Before beginning setup, place a server beneath
the left brew funnel.
1. Insert the funnel into the grinder and select a batch
size to grind. It is not necessary to have coffee beans
in the hopper(s) in order to program the brewer.
The coffee name is pre-selected and stored in the
grinder's memory for the side being ground.
2. Press the GRIND switch. When the grinder stops
grinding, remove the funnel.
3. On the brewer, press and hold the upper right
hidden switch (®) until the display reads
UNITS.
Release the switch, then press switch again until
display reads
SET NEW RECIPE.
4. Press and release
YES
. The display should read
INSERT FUNNEL WITH NEW NAME
, then
USE
LEFT SIDE ONLY
, and finally,
QUIT SETUP?
These
three displays will repeatedly cycle.
5. Insert the funnel into the rails on the left side of
the brewer. The display should read the
NAME
of
the coffee that was ground into the funnel, along
with a
NO
and
YES
. If the
NAME
on the display is
correct, press
YES
.
6. If, for some reason, the name of the coffee from
the grinder did not load properly into the funnel,
or if a grind has not yet been done, the display will
read
MUST GRIND INTO FUNNEL FIRST.
It will be
necessary to grind another batch following steps
1 and 2.
7. If the grind is acknowledged by the brewer, the
display will read
BEGIN SETUP OF (COFFEE NAME)
.
Then the screen will display
BREW OZ
. and a batch
light will be blinking. (Refer to
BREW OZ (SETTING
OR ADJUSTING
for description)
BREW OZ. XX.X
(-) DONE (+)
% BYPASS XX.X
(-) DONE (+)
3 BATCHES DONE?
NO YES
P2415
