Bungard Hellas-E Instructions For Use Download Page 4

Seite 4 / 4

 

We   want     to   tear   your   special   attention   to   a 

careful maintenance of the vacuum foil. It should 

be   cleaned   regularly   using   water   and   a   soft 

detergent. Do not use solvents. 
Be extremely careful not to contaminate the foil 

with spots of developer or etching liquid.
Do  not put pieces with  an height of  more   than 

about 5 mm under the frame. This could lead to 

serious deformation or even cuts in the foil.

Guaranty

All machines are submitted before distribution to 

examination   on   tightness,   function   and  continu-

ous operation firmness. On the machine we grant 

a work warranty of 12 months to our customers 

starting from purchase date on accuracy in ma-

terial and processing. We warrant at our choice 

by exchange of incorrect parts or by repair of the 

machine in our house. Old parts change into our 

possession.

Disclaimer of Warranty

All  parts subjected to wear and the  heater ele-

ment are excluded from this warranty.  This also 

applies to defects to the machine caused by non-

observance of this manual or of parts of it.
We cannot accept subsequent claims from dam-

age or destruction of work pieces worked on in 

the machine, because we have no knowledge or 

control over the operating conditions at your site. 

This is valid in a general manner also for require-

ments from damage to articles, buildings and per-

sons as well as the environment. 
We do not warrant that the function of the ma-

chine   will   meet   the   customer's   requirements   or 

that the operation of the machine will to this re-

gard be error free.
In no event will we be liable to the customer for 

any   incidental,   consequential,   or   indirect   dam-

ages of any kind, including loss of profit and pro-

secution  for environmental  pollution,  even  if  we 

could have been aware of the possibility of such 

damages.
All information was arranged with great care. We 

reserve ourselves however mistake and technical 

changes without previous announcement.

Copyright

We hope to have covered with this information all 

essentials of using the HELLAS exposure set and 

wish you a successful working with this set. If any 

questions this manual does not answer arouse, 

do not hesitate to contact us.

(C) 1989-2013 Bungard Elektronik

Hellas / Hellas-E

Exposure Unit

Instruction for Use 

Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany

Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: [email protected]

Summary of Contents for Hellas-E

Page 1: ...tate your eyes You should therefore avoid to look directly into the light for a longer time Be extremely careful not to contaminate the foil with spots of developer or etching liquid Do not put pieces with an height of more than about 5 mm under the frame This could lead to serious deformation or even cuts in the foil Be cautious not to put any sharp things between the glass board and the foil whe...

Page 2: ...e vacuum frame into a vertical position Place the board s to be exposed onto the glass plate Be sure to have removed any protective foil from the board s Place the artwork onto the board For double sided boards we propose that you mount the top and bottom artwork on an L shaped carrier so that they superimpose and form a bag with lateral stops for the board You will have best results with the emul...

Page 3: ... interrupted and restarted for the remaining time at each time the MODE button is pressed The timer beeps several times when exposure has finished To redisplay the previous setting press the MODE button once You may then use the buttons to change the setting or just restart the unit by pressing the MODE button Do not switch off the vacuum during exposure With the artwork loosing contact to the boa...

Page 4: ...e or destruction of work pieces worked on in the machine because we have no knowledge or control over the operating conditions at your site This is valid in a general manner also for require ments from damage to articles buildings and per sons as well as the environment We do not warrant that the function of the ma chine will meet the customer s requirements or that the operation of the machine wi...

Reviews: