background image

MY22B01 - 12_1.0_26.08.2021

142

Cleaning and servicing

7.3.9.1 Leather saddle  

Leather is a natural product and has similar 
properties to human skin. Regular cleaning and 
care help to prevent leather dehydrating, fading or 
becoming brittle or stained.

1

Remove dirt with a soft, damp cloth.

2

Remove stubborn stains with a leather cleaner.

3

Care for leather saddle after cleaning (see 

Section 7.4.10

).

7.3.10 Tyres 

1

Clean tyres with a sponge, a brush and soap 
cleaner.

2

Rinse off component with water from a 
watering can.

3

Remove any embedded chips and small 
stones.

7.3.11 Spokes and spoke nipples 

1

Clean spokes from the inside to the outside 
with a sponge, brush and soapy water. 

2

Clean rim with a sponge.

3

Rinse off component with water from a 
watering can.

4

Care for spoke nipples after cleaning (see 

Section 7.4.12

).

7.3.12 Hub 

1

Put on protective gloves.

2

Remove dirt from hub with a sponge and soapy 
water.

3

Rinse off component with water from a 
watering can.

4

Wipe off oily dirt with a degreaser and a cloth. 

7.3.13 Switching elements 

1

Clean gear shift, shift cables and transmission 
with water, a brush and dish-washing 
detergent.

2

Rinse off component with water from a 
watering can.

7.3.13.1 Shifter 

Carefully clean shifter with a damp, soft cloth.

7.3.14 Cassette, chain wheels and front 

derailleur 

1

Put on protective gloves.

2

Spray the cassette, the chain wheels and the 
front derailleur with a degreasing agent.

3

Clean coarse dirt with a brush after soaking for 
a short time.

4

Wash down all parts with dish-washing 
detergent and a toothbrush.

5

Rinse off component with water from a 
watering can.

Summary of Contents for 22-15-1078











































































































































































































































Reviews: