Bullet Barbecue 98110 Page 7 Assembly & Operating Instructions Download | Manualshive

Page: 7 / 20

background image

INSTALLATION INSTRUCTIONS

(CONT.)

OUTDOOR NATURAL GAS BBQ INSTALLATION SPECIFICATIONS

NOTE:
- Vents must be provided for combustion air and ventilation on both sides of built-in cabinet.
- When choosing a location for your gas grill keep in mind that it should never be located under any overhead combustible construction.
- The sides and back of the grill should not be any closer than 21 inches to combustible construction.
- DO NOT store empty or full spare tanks under or near this or any other appliance.
- There must be a minimum of 6” counter space behind the grill in order to allow the grill hood to clear properly.

6

«
...
5
6
7
8
9
...
»

Summary of Contents for 98110





















Reviews:

No comments

Related manuals for 98110

Brand: Callow Pages: 8

Brand: Naterial Pages: 156

Brand: Makita Pages: 5

Brand: Makita Pages: 36

Brand: Makita Pages: 2

Brand: Makita Pages: 9

Brand: Makita Pages: 11

Brand: Makita Pages: 6

Brand: Makita Pages: 18

Brand: Makita Pages: 4

Brand: Makita Pages: 12

Brand: Makita Pages: 82

Brand: Makita Pages: 6

Brand: Makita Pages: 40

Brand: Makita Pages: 5

Brand: Makita Pages: 3

Brand: Makita Pages: 12

Brand: GGMgastro Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands