Bulldog Security RS602E Installation And Owner'S Manual Download Page 14

13

Keyless Entry Operation

Press button #2 (lock/unlock), the parking lights will flash once and the doors will lock. Press

button #2 again, the parking lights will flash twice, the doors will unlock,  and the parking lights

will remain on for one minute or until you turn the ignition on or press the brake.

Dome Light Supervision Option

The remote starter includes an optional output that can be used to illuminate the dome light when

pressing button #2 and unlocking your power door locks. The dome light will remain on for one minute

or until you turn the ignition on or press the brake.

Trunk Pop Output

The remote car starter includes an optional output that can be used to do one of the following: open

the trunk (optional relay required), roll up the windows (optional module needed), close the sun

roof (optional module needed) etc. This output will pulse .75 seconds when pressed and released. In

instances where a continuous signal is needed such as sun roof and power windows, hold down Button

#3 (trunk) as long as the signal is needed to complete the task. The parking lights will remain on

as long as this button is being pressed.

Remote Car Finder (Armed Only)

When the unit is armed, press and release Button #4, the horn or siren will chirp three (3) times

and the parking lights will flash three (3) times.

Runtime Confirmation (Disarmed Only)

With the engine off, press and release Button #4 (stop). The parking lights will begin to flash,

each flash represents the programmed runtime. Example: 5 flashes = 25 minutes.

Summary of Contents for RS602E















Reviews: