manualshive.com logo in svg

Bühler technologies P1.1, Installation And Operation Instructions Manual, Page: 16 / 37

Share
Download
Bühler technologies P1.1 Installation And Operation Instructions Manual Download Page 16

P1.1, P1.1E

5.2 Operating the sample gas pump

CAUTION

Risk of injury by moving parts

The device may be damaged if it falls down of by impacts. Pay attention to any accessible
moving parts.
Operation without cover or with damaged cover is not allowed!

The sample gas pump is suitable for delivering gases only. It is not suitable for liquids.

The sample gas pump should be operated without pressure. A system pressure above 0.3 is not allowed. The gas outlet must not
be closed. The flow rate must be at least 50 l/h (150 l/h with system pressure 0.3 bar). If the flow rate continuously is throttled be-
low 150 l/h during operation, the flow rate must be controlled with a bypass valve.

NOTICE

Extreme throttling reduces the life time of the bellow.

If the pump is equipped with a bypass valve, the flow rate can be adjusted. Do not apply force when turning the valve, because
the valve may be damaged otherwise! The turning range of the valve is about 5 turns.

14

Bühler Technologies GmbH

BE420020 ◦ 03/2020

Summary of Contents for P1.1






































Reviews:

No comments