background image

   

 
 

2.3       OPERATING SAFETY 

 
1.

 

Read and understand the Operator’s Manual 
and all safety signs before operating, 
servicing or adjusting. 

 
2.

 

Before servicing or repairing the Model KB 
Series, 

Turn Off Engine, remove key and 

Disconnect Battery Terminals.

 

 

2.4

    

MAINTENANCE SAFETY

 

 
1.

 

Read and follow ALL general, operating, 
maintenance and safety information in this 
manual. 

 
2.

 

Support the machine with blocks or safety 
stands when changing tires or working 
beneath it. 

 
3.

 

Set Blower on the ground, stop engine, set 
park brake, remove ignition key and wait for 
all moving parts to stop before operating, 
servicing or adjusting. 

 
4.

 

Do not adjust the drive belt when it is 
rotating. 

 
5.

 

Make sure all guards are in place and 
properly secured when operating or 
maintaining the Blower. 

 

2.5 

 TRANSPORT SAFETY 

 
1.

 

Make sure you are in compliant with all 
local DOT regulations regarding 
transporting Buffalo Turbine equipment 
on public roads and highways. DOT 
APPROVED TRAILERS ARE 
AVAILABLE FROM BUFFALO 
TURBINE

.  

 
2.

 

ALL SKID MOUNTED UNITS 
 BLOWER UNIT MUST BE 
SECURELY ANCHORED TO 
THE VEHICLE BEING USED 
BEFORE TRANSPORTING OR 
OPERATING. 

   

 
 
 

2.6         STORAGE SAFETY 

 

1.

 

Store the Blower on a firm, level surface. 

 
2.

 

Store away from areas of human activity.  
Do not permit children to play on or around 
the stored machine. 

 
3.

 

Make sure the unit is sitting, or blocked up 
firm and solid and will not tip or sink into a 
soft area. 

 
4.

 

Cover with a weatherproof tarpaulin and tie 
down securely. 

 

2.7        TIRE SAFETY 

               (Model KB Series) 
 

1.

 

Do not attempt to mount a tire unless you 
have the proper equipment and experience to 
do the job. 

2.

 

Have a qualified tire dealer or repair service 
perform required tire maintenance. 

 

 

2.8         SAFETY DECALS 

 

Keep safety decals and signs clean and legible at 
all times. 
 
1.

 

Replace safety decals and signs that are 
missing or have become illegible. 

 
2.

 

Replaced parts that displayed a safety sign 
should also display the current sign. 

 

3.

 

Safety decals or signs are available from 
your Dealer Parts Department

 

 
 
 
 
 
 
 
 
 

 

Summary of Contents for CYCLONE KB4

































Reviews: