2
BT00171-b
-UK
Configuration
The device must be physically configured to set the operating mode:
MODE A:
It is possible to generate up to 40 risers, each with up to 100 handsets (devices).
The total number of handsets installed on the riser column must also include any
handsets and video handsets connected in parallel. With each extra device added in
parallel to the base device, the total number of calls or apartments decreases by one. It
is recommended that the risers in M1 are numbered starting with 1.
The configurators must only be connected to the M1 position. On the generated riser,
handsets (max. 100) must be configured (in N) from 1 to 99.
MODE B:
it is possible to generate up to 100 risers, with the possibility of installing on
each of them a number of handset based on the value of the configurator connected to
M1 and N1. However, the total number of calls in the system is 4000.
The configurators to be used are M1, N1, M2, N2; for each riser these will define the
address of the first and the last video handset of the riser.
In this mode M1 must be the same as M2, and therefore up to 100 call address Handsets
(N1 and N2) may be allocated to each riser.
NOTE:
if only one handset can be installed on a riser
(M1=M2 and N1=N2)
, the
handset shall always be configured with N=1 due to the fact that the call on the 2 WIRE
line (in this configuration) becomes general.
M1 = number of the riser
It allocates to the handsets the number of the riser they belong to
N1 = Call number
Mode A:
MUST not be configured.
Mode B:
it allocates the initial number of the handsets installed on the riser.
M2 = number of the riser
Mode A:
MUST not be configured.
Mode B:
It allocates to the handsets the number of the riser they belong to (it must be
equal to M1)
N2 = Call number
Mode A:
MUST not be configured.
Mode B:
it allocates the final number of the handsets installed on the riser
J =
Selection of the secondary riser entrance panel
It is possible to install a riser EP belonging to the 2 WIRE system range or a riser EP
belonging to the digital system range However, both types of EPs cannot be installed
at the same time.
Configurator J connected = 2 WIRE system EP
Configurator J disconnected = digital system EP (6-8 wires)
PE
IN
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
BUS PI
BUS TK
PS
2
1
OUT M
OUT
M1 N1
M2 N2
JMP
M1
N1
M2
N2
J
J
M
P
M1
N1
M2
N2
2 1 9
2 1 9
M1
N1
M2
N2
1
3 1
3
Handsets
The connected handset must
from 103 to 103
be configured with N =1
Handsets
The connected handset must
from 219 to 219
be configured with N =1
PE
IN
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
BUS PI
BUS TK
PS
2
1
OUT M
OUT
M1 N1
M2 N2
JMP
M1
N1
M2
N2
J
J
M
P
M1
N1
M2
N2
2 1 9
2 1 9
M1
N1
M2
N2
1
3 1
3
346150
