![background image](http://html.mh-extra.com/html/bt/tm-7/tm-7_owners-manual_2824490011.webp)
B
T
P
A
I
N
T
B
A
L
L
.
C
O
M
10
13. General Maintenance
CAUTION:
Before attempting to perform any maintenance operations,
make sure that all paintballs and propellant sources have been removed
from the marker and that the regulator gauge reads 0 psi. Install a bar-
rel blocking device, move the Selector switch to the OFF position and push
Power button and hold for over 2 seconds until the LED light changes
from Red to Green, and keep the TM-7 power OFF.
Keep your TM-7 clean and lubricated to eliminate the friction that would
prevent reliable operation. Clean and lube the marker before each use,
and do not put it away dirty. Do not use oils made for paintball markers,
real firearms or pneumatic tools, do not use oils at all. Do Not use petro-
leum-based lubricants in the lubrication of this marker. Teflon or silicon
(NON-spray only) lubricants designed for use on o-rings may be used for
lubrication for the bolt, bolt guide and poppet area only. Only use grease
supplied with your TM-7.
The outer plastic shell can be rinsed with warm water once all the internals
have been removed. Make sure it is fully dry before reassembling the TM-7.
Notes:
• Do not rinse the Tm-7 Shell under water without fully disassembling the
marker, as you will damage the electronics.
• Do Not work on your TM-7 until the Air source is removed and it is verified
that the regulator gauge reads 0 psi and no air is trapped in the TM-7.
14. TM-7 Assembly/Disassembly
CAUTION:
Before attempting to perform any marker disassembly, make
sure that all paintballs and propellant sources have been removed from
the marker and that the regulator gauge reads 0 psi. Install a barrel
blocking device, move the Selector switch to the Safety position and push
Power button and hold for 2 seconds until the LED light changes from Red
to Green, and keep the TM-7 power OFF.
Disassembly Tips
• Make sure you have a clean area to work on your marker.
• Do not remove the Air Transfer tube from the body and regulator; these
parts are assembled tightly at the factory to prevent leaks.
• When separating the Shell for the first time, locate the Selector shaft
and Trigger, notice their position for easy reassembly.
• Make sure the Main spring is installed correctly on the Bolt, as it needs
to be installed in the right direction.
• Install the Stock lock and Stock at the same time. Install the Stock lock
into the Stock arms and place them in the shell at the same time.
• After reassembling the TM-7 recheck your trigger activation settings.
Visit PaintballSolutions.com for additional information.
Barrel
It is recommended that the barrel be removed before and other mainte-
nance or disassembly is performed. Simply turn the barrel counter-clock
wise to remove. Use warm water and a barrel cleaning device to keep the
Barrel in top condition.
Rear Sight
The rear sight rail can be removed by loosening the screw with a 1/8”
Allen wrench and then lift the rear sight off.
Feed Elbow
To remove the feed elbow, push the release button on the left side of the
feed elbow and slide it forward about 1 inch and lift it off. The Feed elbow
does not slide off the front of the rail.
Summary of Contents for TM-7
