BT LPE200 Service Manual Download Page 148 | Manualshive

Page: 148 / 154

background image

11- 6

Service Guide

LWE180, LWE200, LPE200, LPE240

© BT Europe AB

Hydraulic/Pneumatik – 6000 LWE 180/200 LPE 200

Adjusting the pressure limit valve

T-code

Valid from serial number

Date

Order number

660, 661, 662, 497

723984-

2005-05-11

225553-040

11.6 Adjusting the pressure limit valve

The pressure limit valve is set to the correct value at the factory, but
may need to be adjusted if the valve or the complete hydraulic unit is
replaced.

The truck should be capable of lifting a load of between 2050-2100 kg.

1.

Locking nut.

2.

Adjuster screw, pressure limit.

Adjusting clockwise results in increased pressure.

Adjusting anticlockwise results in decreased pressure.

•

Loosen the locking nut (1) using a 13 mm spanner.

•

Place a load of 2000 kg on the forks and check that the truck can lift
it.

•

If the truck lifts 2000 kg, place a further 100 kg on the forks. Check
whether the truck can lift the load.

•

If the truck lifts 2100 kg, adjust the pressure limit by turning the ad-
juster screw (2) anticlockwise using a 4 mm allen key until the truck
cannot lift the load.

«
...
146
147
148
149
150
...
»

Summary of Contents for LPE200



























































































































































Reviews:

No comments

Related manuals for LPE200

Brand: marsden Pages: 14

Brand: Linde Pages: 168

Brand: KAUP Pages: 29

Brand: ep Pages: 68

Power Stak PPS2200-62NAS

Brand: Presto Lifts Pages: 60

Brand: Jungheinrich Pages: 81

TIGRIP TKG 1,0 vh

Brand: CMCO Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands