"
Indicator:
DEFROST" indicator blinks when it is defrosting. It will automatically returns to run mode after a while. Defrost only
happens in very cool place. Do not operate the unit in excessively cold place. General recommendation of
best operating temperature is 18 deg C to 35 deg C, though the unit remain function-able above 10 deg C.
When the temperature is too cold, it could create a frost in the refrigeration system and damage the compressor.
3 indicating lights are on top of the control panel. The Operation light is on when the machine starts. Note: If the surrounding
air RH is lower than the set value at the knob, the machine will remain switch off. This is perfectly normal. It mean that
there is no need for further drying because the room RH has reached the desired RH level set on the machine.
The Tank Full light is on when the water container is full. When this happens, the machine will stop to prevent flooding.
How to make continuous drainage:
You may plug in a 12.5 - 14mm ( internal
diameter) hose for continuous drainage.
in this case, the bucket will be empty all
the time. First use a screw drive to remove
or knock out the broken line plastic cap at
the back of the machine, then push the
hose through to the water container side.
Cut a “V” groove on the hose. Soft hose
Filter maintenance
If the filter is covered with plenty of dust, the air flow and the performance of the unit
will be affected and noise will increase. It is recommended to check the filter condition
every 2 months. To clean filter : first turn off the power. Remove the water container.
Pull down the filter as in the picture. Vacuum the nylon filter or clean it with clean water
( or with soap and rinse it ).
To clean the body : Clean the air inlet and air outlet with a damp soft cloth as these parts
gather dust easily. DO NOT USE petrol or chemical solvent.
Remove water container and look up
to the left corner for the nipple.
Make sure the soft hose is straight.
An upward curve which causes water
to flow backward will allow water
to leak back to the container instead
of running thro’ the hose. Add an elbow
joint to ensure no water trapped within pipe.
PVC hose
“V” shape cut to PVC hose
internal Dia.:12.5 to 14 mm
Thickness: 2 mm
Internal nipple
joint
Hose clip
OTHER PRECAUTION :
1) ENSURE THAT THE RIGHT VOLTAGE AND FREQUENCY IS USED. ( 220-240 VAC 50 HZ)
2) NEVER TILT THE UNIT AT AN ANGLE OR PUT IT IN A HORIZONTAL POSITION AT ALL TIME BE IT OPERATING
OR NOT. DO NOT DRAG THE UNIT OVER VERY ROUGH SURFACE.
3) DO NOT PLACE THE UNIT FACING THE WALL. ENSURE THAT THERE IS AT LEAST 100 mm ( 4 inches )
SPACE BETWEEN WALL AND THE FRONT OF THE DEHUMIDIFIER. FOR SMALL CLOSET USAGE, ENSURE
TEMPERATURE INSIDE THE ROOM IS NOT ABOVE 30 DEG C.
4) THE MACHINE IS DESIGNED FOR ENCLOSED SPACE USAGE ONLY. DOORS AND WINDOWS ARE TO BE
CLOSED FOR THE DEHUMIDIFIER TO OPERATE NORMALLY. OPEN WINDOWS / DOORS INCREASE EXCESS
WORK LOAD ON THE MACHINE AND WILL CAUSE DAMAGE BY OVER LOADING THE MACHINE.
5) DO NOT OPERATE THE MACHINE NEAR 35 DEGREE C OR ABOVE OR A POTENTIALLY HOT PLACE.
DO NOT USE IT IN A DUSTY OR CHEMICAL ENVIRONMENT OR UNDER DIRECT SUNLIGHT OR RAIN.
6) DO NOT SHIFT THE MACHINE FROM A VERY COLD ROOM TO A WARM ROOM IMMEDIATELY. AS
WATER DROPLETS MAY FORM ON THE ELECTRONICS INSIDE. IF SUCH SHIFT HAS TO BE DONE,
FIRST WRAP THE UNIT IN A LARGE PLASTIC SHEET / BAG WHILE IT WAS IN THE COLD ROOM.
SHIFT IT OVER AND DO NOT OPEN IT UP FOR THE NEXT FIVE HOURS.
of 2 mm thickness or less is recommended. Mount the hose on the nipple accessed from the water container side
and tight it around with a cable tie or a hose clip. Make sure all the part of the hose that comes out must be lower
in height then the drainage outlet to prevent back flow. The drainage uses gravity to drain out water. Any higher
piping will cause back flow the create water leakage.
Page 2 of 2
