BSS Audio DPR-901ii User'S Manual And Operation Manual Download | Manualshive

Page: 6 / 30

background image

6

DPR-901ii

Installation
Unpacking
Mechanical Installation

As part of BSS AUDIO’s system of quality control, this product is
carefully checked before packing, to ensure flawless appearance.

After unpacking the unit, please inspect for any physical damage and
retain the shipping carton and all relevant packing materials for use
should the unit need returning.

A packet of spare fuses is supplied. Please keep them in a safe place.

If any damage has occurred, please notify your dealer immediately, so
that a written claim for damages can be initiated. See the Warranty
section of this manual.

A vertical rack space of 1U (1.75", 44.5mm) is required. Figure 2.1
details the relevant dimensions and fixing centres.

If the unit is part of a transportable system, you must support the unit at
it’s rear by additional bracing or shelving . Failure to do so will impair
reliability and invalidate the Warranty. Additional threaded M3 screw
holes are provided on the rear sides to assist in providing proper
support.

Adequate ventilation must be provided for by allowing sufficient room
around the sides and rear of the unit to allow free circulation of air.
Forced cooling is not required.

2.0

Installation

2.1 Unpacking

Fig. 2.1 Mechanical

Dimensions

2.2 Mechanical

Installation

«
...
4
5
6
7
8
...
»

Summary of Contents for DPR-901ii































Reviews:

No comments

Related manuals for DPR-901ii

Brand: Elta Pages: 142

Brand: Cyrus Pages: 6

Brand: Aiwa Pages: 30

Personal PA Receiver PPA R19

Brand: Williams Sound Pages: 2

Bell'O Digital BDSW-1650-BLK

Brand: Twin-Star International Pages: 20

Brand: Panasonic Pages: 24

Brand: Suzuki Pages: 150

Brand: Sony Pages: 74

Brand: Denver Pages: 32

Brand: Denver Pages: 73

Brand: Aiwa Pages: 62

Brand: Aiwa Pages: 42

Brand: auna Pages: 100

Brand: Hyundai Pages: 52

Brand: DEGEN Pages: 21

Brand: E-Mu Pages: 64

Brand: Hyundai Pages: 40

Brand: Repeater Builder Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands