Bryston BP16 Owner'S Manual Download Page 5

BP16 

PREAMPLIFIER

3

selected the 12Vdc control voltage will be removed 

from  these  pins.  Please  note  that 

C

  means  “com-

mon”  here  and  both 

C

  pins  are  electrically  con-

nected and identical. 

PROGRAMMING the “T2” 12v 

TRIGGER OUTPUT:

By default the 

T2

 triggered output is inactive. To pro-

gram this output to become active , whereupon a 

control voltage of 12Vdc will appear across 

T2

 & 

C

 

terminals whenever a specific source is selected, use 

the handheld remote control as follows:

•   Select the source that you want to coincide with 

T2

 going active.

•   While pointing the remote control at the BP16, 

press the 

CODE 

button, followed by the three digit 

code “247” using the keys numbered 1 through 0 

in the illustration at the left. On your remote con-

trol these keys, or buttons, are labeled 

AUX/PH 

(2), 

TUNER

 

(4), 

D1 

(7). 

•   The three digit code should be entered within a 

few seconds of pressing 

CODE

 button or the unit 

will automatically return to normal operation.

•   To clear the 

T2

 trigger output, press the 

CODE 

but-

ton followed by the 3 digit code “248”: 

AUX/PH

 (2), 

TUNER

 (4), 

D2

 (8). 

HAND-HELD INFRA-RED REMOTE 

CONTROL:

The  Bryston  model  BP16  comes  stan-

dard with a full function hand-held remote 

control unit. The hand held remote unit 

is powered by two “AAA” batteries.  To 

change  the  battery  remove  the  bottom 

cover plate by removing the four Philips 

screws  on  the  rear  of  the  remote  unit.  

Ensure  that  the  batteries  are  correctly 

oriented and properly seated in the bat-

tery holder.

The  BP16  remote  is  a  full  function 

remote. It allows selection of all sourc-

es,  volume  up  or  down  (the  volume 

control is a motor-driven design), mute 

,left/right  balance,  power  on/off  and 

discrete code entry.

We recommend maintaining a direct line-

of-sight between the hand held remote 

unit and the front of the BP16 to ensure the most efficient 

operation of the remote features. 

PROGRAMMING the HANDHELD 

REMOTE CONTROL:

The  automatic  motion-sensing  backlight  function  in  the 

handheld infra-red remote control unit can be disabled by 

entering the 3 digit code “792” as follows:

1)   Press  and  hold  the 

CODE 

button  for  5  seconds. 

Release when the LED flashes red.

2)   After the LED stops flashing, enter the 3 digit code 

“792”  by  pressing  the  buttons 

D1

D3

  then 

AUX/PH 

(see illustration on page 3)

3)   To re-enable the motion-sensing backlight function, 

repeat steps 1 and 2 above

To  completely  disable  the  backlight,  enter  the  3  digit 

code “797” as follows:

1)   Press  and  hold  the 

CODE 

button  for  5  seconds. 

Release when the LED flashes red.

2)   After the LED stops flashing, enter the 3 digit code 

“797”  by  pressing  the  buttons 

D1

D3

  then 

D1 

(see 

illustration on page 3)

3)   To  re-enable  the  backlight  repeat  steps  1  and  2 

above

SENDING CODES to the BP16 via the IR 

HANDHELD REMOTE CONTROL:

Press the CODE button on the remote control (the red 

LED will light) and then enter the 3 digt code, as listed in 

the “Wired RS-232 Remote Control” section” below.  The 

LED  will  flash  to  confirm  transmission  and  then  extin-

guish.

WIRED RS-232 REMOTE CONTROL:

Using the DB9 female connector at the rear of the unit, 

the  BP16  can  receive  commands  via  a  null  modem 

cable at 9600 baud, 8 data bits, no parity and 1 stop bit 

(9600,8,N,1). Valid commands will return the “>” charac-

ter indicating that the unit is ready to receive a new com-

mand. An invalid command will return the “!” character. 

These serial data commands are as follows:

000 - power off 

001 - select analog source 1 (A/d)  

002 - select analog source 2 (AuX/PH)

003 - select analog source 3 (cd) 

004 - select analog source 4 (tuner) 

005 - select analog source 5 (tv) 

006 - select analog source 6 (vIdeO)

007 - volume up

008 - volume down 

015 - power on/off toggle

019 - balance left 

020 - balance right 

Reviews: