background image

BRYSTON 20 -YEAR WARRANTY

Bryston products are warranted to be free from
manufacturing defects for a minimum of twenty
years from the original date of manufacture. This
includes parts, labour and return shipping to the
first owner and all subsequent owners. Warranty
coverage is automatic and commences with the
original date of manufacture which is kept on file at
Bryston.

In the event of a defect or malfunction, Bryston will
remedy the problem by repair or replacement, as
we deem necessary, to restore the product to full
performance. 

This warranty is considered void if the defect, mal-
function or failure of the product or any component
part was caused by damage ( not resulting from a
defect or malfunction ) or  abuse  while in the pos-
session of the customer. Tampering by persons
other than factory authorized service personnel, or
failure to fully comply with Bryston operating
instructions, voids the warranty.

This warranty gives you specific legal rights and
you may also have other rights which may vary
from province to province and country to country.

BRYSTON LTD., 677 NEAL DRIVE, P.O. BOX 2170, PETERBOROUGH, ONTARIO CANADA K9J 7Y4

BRYSTON SERVICE OUTSIDE CANADA & the USA:

CONTACT YOUR LOCAL DISTRIBUTOR 

OR

CHECK OUR WEB SITE:

www.bryston.ca 

E-MAIL BRYSTON DIRECTLY:

[email protected]

FAX BRYSTON DIRECTLY:

705-742-0882

PHONE BRYSTON DIRECTLY:

705-743-5325

BRYSTON SERVICE USA:

79 COVENTRY ST., SUITE #5

NEWPORT VERMONT. 

U.S.A. 05855-2100

PHONE: 802- 334-1201

FAX: 802-334-6658

E-mail:  [email protected]

BRYSTON SERVICE CANADA

:

24 STEINWAY BLVD., UNIT 48

ETOBICOKE, ONTARIO

CANADA M9W 6T8

PHONE: 416-675-2585

FAX: 416-675-3103

E-mail:  [email protected]

Summary of Contents for 875 Z













Reviews: