Bryston 3B SST C Owner'S Manual Download Page 13

3B SST and 4B SST Series Amplifiers

13

3BSST                          Technical Specifications

4BSST

Power Output

150 watts per channel into 8 ohms 
250 watts per channel into 4 ohms 

Gain Select and Sensitivity

29dB - 1.3Vin = 150W @ 8 Ohms - (1V Position)
23dB - 2.6Vin = 150W @ 8 Ohms - (2V Position)

Input Impedance

50 Kohms single ended
20 Kohms balanced 

Distortion IM or THD+noise

< 0.005% 20Hz to 20kHz at 150 watts into 8 

W

< 0.007% 20Hz to 20kHz at 250 watts into 4 

W

Noise 

Measured with input shorted -  20Hz to 20kHz.
>110dB below rated output 29dB gain (- 75dBu)
>113dB below rated output 23dB gain (- 78dBu)

Slew Rate  

> 60 volts per microsecond 

Power Bandwidth

< 1 Hz to over 100 kHz 

Damping Factor   

Over 500 at 20 Hz, ref. 8 ohms 

Dimensions

19” version with handles - L x H x D

48.3 x 13.3 x 32cm  - 19” x 5.25” x 12.5“  
mounted rack depth -  28cm  - 11.0" 

17” version

43.2 x 13.3 x 28cm  -  17” x 5.25” x 11“

Weight:

approx.  18kg - 40 lbs 

Power Consumption & Heat Load 

At Idle  - 

127 Watts

Max. Heat Dissipation -                 433 Btu/Hr.

2 channels @ 150W @ 8 ohms -   668  Watts 

Max. Heat Dissipation 8 ohms -  1255 Btu/Hr.

2 channels @ 250W @ 4 ohms -  1096 Watts  
Max. Heat Dissipation 4 ohms -    2033 Btu/Hr.      

Bridged @ 450W @ 8 ohms  - 

1053 Watts

Max. Heat Dissipation 8 ohms -    2057 Btu/Hr.

Power Output

300 watts per channel into 8 ohms 
500 watts per channel into 4 ohms 

Gain Select and Sensitivity

29dB - 1.8Vin = 300W @ 8 Ohms - (1V Position)
23dB - 3.6Vin = 300W @ 8 Ohms - (2V Position)

Input Impedance

50 Kohms single ended
20 Kohms balanced 

Distortion IM or THD+noise

< 0.005% 20Hz to 20kHz at 300 watts into 8 

W

< 0.007% 20Hz to 20kHz at 500 watts into 4 

W

Noise 

Measured with input shorted -  20Hz to 20kHz.
>110dB below rated output 29dB gain (- 75dBu)
>113dB below rated output 23dB gain (- 78dBu)

Slew Rate  

> 60 volts per microsecond 

Power Bandwidth

< 1 Hz to over 100 kHz 

Damping Factor   

Over 500 at 20 Hz, ref. 8 ohms 

Dimensions

L x H x D 

19” version with handles - 
48.3 x 13.3 x 43.8cm  - 19” x 5.25” x 17.25“  
mounted rack depth -  40.1cm  - 15.75" 
17” version
43.2 x 13.3 x 40.1cm  -  17” x 5.25” x 15.75“

Weight:

approx.  22kg - 50 lbs 

Power Consumption & Heat Load 

At Idle  - 

170 Watts

Max. Heat Dissipation -                 580 Btu/Hr.

2 channels @ 300W @ 8 ohms -  1280  Watts 

Max. Heat Dissipation 8 ohms -  2320 Btu/Hr.

2 channels @ 500W @ 4 ohms -  2100 Watts  
Max. Heat Dissipation 4 ohms -    3750 Btu/Hr.         

Bridged @ 900W @ 8 ohms  - 

2040 Watts

Max. Heat Dissipation 8 ohms -    3890 Btu/Hr.

Summary of Contents for 3B SST C















Reviews: