manualshive.com logo in svg

Bryant 582J 04-06, Installation Instructions Manual

Share
Download
Bryant 582J 04-06 Installation Instructions Manual Download Page 39

39

COMPLETING RETURN AIR SMOKE SENSOR 

INSTALLATION
1. Unscrew the two screws holding the Return Air Smoke

Detector assembly. See Fig. 53, Step 1. Save the screws.

2. Turn the assembly 90 degrees and then rotate end to end.

Make sure that the elbow fitting is pointing down. See Fig.

53, Step 2.

3. Screw the sensor and detector plate into its operating posi-

tion using screws from Step 1. See Fig. 53, Step 3. 

4. Connect the flexible tube on the sampling inlet to the sam-

pling tube on the basepan.

ADDITIONAL APPLICATION DATA
Refer to the Application Data sheet titled Factory Installed Smoke

Detectors for Small and Medium Rooftop Units 2 to 25 Tons for

discussions on additional control features of these smoke detectors

including multiple unit coordination.

RTU Open Controller (Factory-Installed Option)

For details on operating 582J*04-06 units equipped with the facto-

ry-installed RTU Open controller refer to the “

Factory-Installed

RTU Open Multi-Protocol Controller Control, Start-Up, Opera-

tion and Troubleshooting

” manual.

Step 14 — Adjust Factory-Installed Options

SMOKE DETECTORS
Smoke detector(s) will be connected at the Controls Connections

Board, at terminals marked “Smoke Shutdown.” Cut jumper JMP

3 when ready to energize unit.
ECONOMI$ER IV OCCUPANCY SWITCH
See Fig. 54 for general EconoMi$er IV wiring. External occupan-

cy control is managed through a connection on the Controls Con-

nections Board.
If external occupancy control is desired, connect a time clock or

remotely controlled switch (closed for Occupied, open for Unoc-

cupied sequence) at terminals marked OCCUPANCY. Cut jumper

JMP 2 to complete the installation.

Step 15 — Install Accessories

Available accessories include:

• Curb
• Thru-base connection kit (must be installed before unit is

set on curb)

• LP conversion kit
• Flue discharge deflector
• Manual outside air damper
• Two-position motorized outside air damper
• EconoMi$er

®

 IV (with control)

• EconoMi$er 2 (without control/for external signal)
• Power Exhaust
• Differential dry-bulb sensor (EconoMi$er IV)
• Outdoor enthalpy sensor
• Differential enthalpy sensor
• CO

2

 sensor

• Louvered hail guard
• Motormaster

®

 head pressure controls

• Phase monitor control

Refer to separate installation instructions for information on in-

stalling these accessories.

Fig. 53 — Completing Installation of Return Air Smoke Sensor

S

TEP 1

S

TEP 2

S

TEP 

3

Summary of Contents for 582J 04-06













































Reviews:

No comments

Brands by name

Popular brands

Load more brands