background image

— 10 —

Maintenance Schedule / Check List

ITEM

TYPE OF MAINTENANCE

FREQUENCY

Blade carrier to bearing 
housing bolts 

Torque to 380 ft - lbs for the 3 & 4 blade carri-
er assemblies.

Daily or every 8 hours

Blade Bolt/nuts

Torque to 540 ft - lbs for the 3 drop blades.

Torque to 270 ft - lbs for the 4 flat blades.

Daily or every 8 hours

Blade Inspection

Check for damage, dullness or cracks. Blades 
should rotate freely and be clear of obstruc-
tions. Replace entire set of blades if damaged.

Daily or every use

Bearing Housing

Remove any foreign material from shaft.

Daily or every use

Hoses and hose safety shield Check for wear or damage. 

Daily or every 8 hours

Hydraulic Motor Mount 
Bolts

Torque to 75 ft - lbs.

Daily or every 8 hours

Bearing housing lubricant

Check oil - add 80 W 90 gear oil - 

DO NOT 

over fill - The bearing housing is full when oil 
level is 2” below the plug cap. 

Once per week

Push Guard

Clean the fitting before lubrication. Apply 
grease to the pins on the guard of the 72 
M-AX.

As needed

72 M-AX Unit

Clean the unit to view potential damage or 
obstructions that could result in poor perfor-
mance.

As needed

  
  

CAUTION: 

  Perform maintenance on a level surface with the unit    

 

 

 

 

firmly on the ground. Shut off the hydraulic power sup- 

 

 

 

 

ply and disconnect hydraulic couplers.

  

Do Not 

loan your 72 M-AX to another skid steer owner.  

 

 

 

 

The potential exists for hydraulic contamination 

 

 

 

 

 

and could shorten the life of your skid steer or the  

 

 

 

 

 

hydraulic motor on your 72 M-AX.

Summary of Contents for 72 M-AX





















Reviews: