III. INsTRuCTIoNs FoR use
Before you can use the appliance, its batteries must be charged. The operation time for
one charge depends on the attachment used and workload. The time with the big cutting
attachment is around 90 minutes. With the smaller attachments, this time is significantly longer.
To Charge/Recharge
–
Fully charge Clipper before using for the first time or after non- use for a long period of time.
–
Battery performance is best if you recharge only when the battery is (almost)completely empty.
–
Charging or recharging at temperatures below 10°C or higher than 40°C adversely affects
lifespan of the battery.
–
Continuously recharging Clipper will reduce lifespan of battery.
1) Be certain Clipper is
OFF
.
2) Charging: plug the connector into the socket
A5
or into the dock and accessory holder
(see pic. 2), where you place the trimmer (socket
D5
).
3) Plug charging plug into any 230V AC outlet. Use only the cord provided
4) It will take approximately 0,5 - 2 hours to fully charge the Clipper.
5) Do not exceed the set time of charging! There is an indicator light
A2
on during charging.
When the battery is charged, green light turns on.
6) After charging, unplug the adaptor from the mains first and only then unplug the
connector from the appliance.
Optimize the working life of the battery
–
Do not charge for more than 2 hours.
–
Do not keep cord permanently plugged in.
–
The appliance heats up during charging or operation, which is normal.
First select the attachment you want to use for cutting purposes. You have 5 different cutting
attachments with different uses to choose from. All these cutting attachments (
B1, B2, B3,
B4, B5
) are put on the appliance in the same manner. Follow instructions on pic. 3. First
put the desired attachment to the bottom part of the space for the attachment head (pic.
3A). Then fold the remaining part of the attachment on by pressing lightly (pic. 3B). Correct
fixation of the attachment is indicated by an audible click (pic. 3C. When removing the
attachment, proceed reversely. Press lightly on the fixed attachment from the front part of
the attachment. This will release it, you can now remove it.
Cutting attachments
B1
and
B2
can be used with comb attachments with various length of
cutting. All these comb attachments C are put on in the same manner (follow the instructions
on pic. 4A, 4B, 4C
1
). When removing the comb attachment, proceed reversely (pic. 4C
2
).
Hair clipping
–
The trimmer can be operated from the outlet with the adaptor connected or only from the
charged battery. In case an attachment
B
gets blocked (or the blades
A3
), the appliance
must be turned off immediately and the cause of the block removed.
–
The trimmer turns on and off with a switch
A1
. Turn the trimmer on only after all the
attachments have been properly placed and you are ready for trimming. Turn the trimmer
off immediately after use.
–
We recommed oiling the blades with the oil
D4
attached before first use.
–
Before you start clipping, make sure that the head of the person whose hair you are
cutting is at the same level as your chest so that all parts of his/ her head are clearly
visible and within easy reach.
GB
27
/ 53
Summary of Contents for eta 6342
