Bruker BEST Installation Manual Download | Manualshive

Page: 9 / 29

background image

Installation Manual Version 004

9 (29)

3

Mounting the
Barcode Reader

3

Mounting the Barcode Reader on the Gilson Liquid Handler

3.1

1. Mount the barcode reader on the barcode reader bracket using the 2 M3x8

hexagon screws, as shown below:

Figure 3.1. Mounting the Barcode Reader to the Bracket

2. Mount the barcode reader bracket on the Z-tower of the Gilson Liquid Handler

using the two M3x10 cylinder screws. Ensure that you mount the bracket just
under the top plate of the Z-tower cover. There should not be a gap between
the Z-tower cover and the bracket (as shown in

Figure 3.2.

2x M3x8
Hexagon
Screws

Barcode Reader Bracket

«
...
7
8
9
10
11
...
»

Summary of Contents for BEST






























Reviews:

No comments

Related manuals for BEST

Brand: Wasp Pages: 27

QuickScan QM2430-BK-433K2

Brand: Datalogic Pages: 40

Brand: Aiwa Pages: 22

Brand: Stid Pages: 16

Brand: Marson Pages: 16

Brand: SAMSys Pages: 60

Brand: Krüger & Matz Pages: 40

Brand: Hand Held Products Pages: 144

Brand: Leuze electronic Pages: 22

Brand: Xtool Pages: 19

Brand: Optoelectronics Pages: 30

Brand: Elite Pages: 2

EZ6000 Plus Series

Brand: Godex Pages: 2

Brand: U-Prox Pages: 4

Brand: Viking Pages: 4

Brand: Unitech Pages: 2

ACW/LW8-DIND160

Brand: Wireless Pages: 41

Brand: i-tec Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands