Bruker BioSpin BLAH2000-I E C Operating & Service Manual Download Page 42

Page: 42 / 48

42 (47)

BRUKER BIOSPIN

Operating & Service Manual Version 001

Service Information and Maintenance

Figure 8.1. Fan Supplies and Status Connections

4. Unscrew only the 4 screws from the top of the Push and Pull fan assemblies

on the both sides of the RF module.

Figure 8.2. Push Fan Assembly

5. Remove the Push and Pull fan assemblies.

6. Place correctly the new fan assembly sets in the bottom holes of the RF

module and screw it on the top.

7. Connect the 2 red/white wires on the left side of the RF module (J3 and J4).

8. Connect line cord and turn on the amplifier. Note that the fans are turning and

no OVERHEAT status led appears on front panel.

9. Turn off the amplifier and disconnect the line cord.

10. Put the coverage plate on the amplifier and screw it.

11. Put the amplifier in the CLINSCAN console, connect all cables on the front

panel and the line cord on the rear panel.

Pull fan

connector J3

Push fan

connector J4

Screws for Push an Pull

fan assemblies

Summary of Contents for BLAH2000-I E C

















































Search results

Summary of Contents for BLAH2000-I E C

Reviews:

Related manuals for BLAH2000-I E C

Brands by name

Popular brands

Bruker BioSpin BLAH2000-I E C, Operating & Service Manual

Search results

Summary of Contents for BLAH2000-I E C

Reviews:

Related manuals for BLAH2000-I E C

Brands by name

Popular brands