manualshive.com logo in svg

BROWN 400 Series, Operator'S Manual

Share
Download
BROWN 400 Series Operator'S Manual Download Page 16

WARNING

Wear  protective 

clothing.

Warning!  Wear protective 

clothing.

Wear  close-fitting  clothing  and  other  protective 

devices appropriate for the job.

Equipment Safety

16

Warning!  Slopes and 

rough terrain.

When operating on slopes or rough terrain, decrease 

travel speed.  Do not operate in an area where the 

tractor could roll over.  

Be sure to fasten safety 

belt when operating tractor!

Warning!  Roll-over 

protection.

Do  not  operate  the  mower  on  any  tractor  not 

equipped with a certified roll-over protective struc

-

ture (ROPS).

WARNING

Slow travel speed 

when operating on 

slopes or rough ter-

rain.

WARNING

Use only with

tractors equipped

with a certified

roll-over protective

structure.

DANGER

Danger!  Tighten blade 

bolts.

Blade bolts will stretch with use and must be tight-

ened.  Follow maintenance instructions in this man-

ual (see page 21).  

If the mower is operated with 

loose blade bolts, blades and blade carrier will be 

damaged.  Operation with damaged blades and 

blade carrier  will lead to blade ejection and will 

cause serious injury or death.

Tighten blade bolts 

as  prescribed  in 

owners  manual.  

Ejection  of  blade 

will  cause  serious 

injury or death.

Summary of Contents for 400 Series







































Reviews:

No comments

Brands by name

Popular brands

Load more brands