manualshive.com logo in svg

Brother MFC-9140CDN, User Manual

Share
Download
Brother MFC-9140CDN User Manual Download Page 95

Routine maintenance 

85

A

h

Clean the corona wire inside the drum 
unit by gently sliding the green tab from 
left to right and right to left several times.

 

NOTE

Be sure to return the tab to the Home 
position (

a

) (1). The arrow on the tab must 

be aligned with the arrow on the drum unit. 
If it is not, printed pages may have a 
vertical stripe.

 

i

Repeat step

c

 and step 

h

 to clean 

each of the three remaining corona 
wires.

NOTE

When cleaning the corona wires, you do 
not have to remove the toner cartridge 
from the drum unit.

 

j

Slide each toner cartridge and drum unit 
assembly into the machine. Make sure 
you match the toner cartridge colour to 
the same colour label on the machine.

 

 

BK = Black, C = Cyan, 
M = Magenta, Y= Yellow

1

BK

C

M

Y

Summary of Contents for MFC-9140CDN




















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands