manualshive.com logo in svg

Brother MFC 7345N - Laser Multifunction Center, User Manual

Share
Download
Brother MFC 7345N - Laser Multifunction Center User Manual Download Page 140

126

Replacing the consumable items

B

You will need to replace the consumable items when the machine indicates that the life of the 
consumable is over.

Note

• Go to http://www.brother.com/original/index.html for instructions on how to return your used 

consumable items to the Brother collection program. If you choose not to return your used 
consumable, please discard the used consumable according to local regulations, keeping it 
separate from domestic waste. If you have questions, call your local waste disposal office. Be 
sure to reseal the consumable items tightly so that the material inside does not spill.

• We recommend placing used consumable items on a sheet of paper to prevent accidentally 

spilling or scattering the material inside.

• If you use paper that is not a direct equivalent for the recommended paper, the life of 

consumable items and machine parts may be reduced.

 

Replacing a toner cartridge

B

The High Yield toner cartridges can print 
approximately 2,600 pages

1

 and the 

Standard toner cartridges can print 
approximately 1,500 pages

1

. Actual page 

count will vary depending on your average 
type of document (i.e., standard letter, 
detailed graphics).
The machine is supplied with the Starter 
toner cartridge that will need to be replaced 
after approximately 1,000 pages

1

. When a 

toner cartridge is running low, the LCD shows 

Toner Low

. 

1

Approx. cartridge yield is declared in accordance 
with ISO/IEC 19752.

Note

It is a good idea to keep a new toner 
cartridge ready for use when you see the 

Toner Low

 warning.

 

Toner cartridge

Drum unit

 

 

Order No. TN-330, TN-360

Order No. DR-360

Summary of Contents for MFC 7345N - Laser Multifunction Center

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands