LK3
−
B438E Mark II 2/9
2000.7
LK-B438E Mark II List of pre-programmed patterns
Sewing patterns are limited as shown in the table below.
(Any program is available as long as the needle drops down in the hole of the button.)
Program
No.
Sewing
pattern
No. of
threads
No. of
crossover
stitches
No. of
stitches
Sewing
size
X-Y
(mm)
Program
No.
Sewing
pattern
No. of
threads
No. of
crossover
stitches
No. of
stitches
Sewing
size
X-Y
(mm)
1
6
-
13
18
6 - 6
1
20
2
8
-
15
19
8 - 8
1
24
3
10
-
17
31
10 - 10
1
28
4
12
-
19
45
12 - 12
1
32
5
*1
16
-
23
20
*3
6 - 6
0
26
6
*1
20
-
27
3.4 × 0
32
*3
8 - 8
0
30
7
*2
6
-
13
33
*3
10 - 10
0
34
3.4 × 3.4
23
*2
10
-
17
21
*2
6 - 6
1
20
8
*2
12
-
19
0 × 3.4
34
*2
10 - 10
1
28
9
*2
5 - 5 - 5
-
22
22
*2 *3
6 - 6
0
26
24
*2
7 - 7 - 7
-
28
35
*2 *3
10 - 10
0
34
2.4 × 3.4
25
*2
5 - 5 - 5
-
22
46
6 - 6
1
20
26
*2
7 - 7 - 7
-
28
2.6 × 2.4
47
8 - 8
1
24
10
6 - 6
1
20
48
10 - 10
1
28
11
8 - 8
1
24
49
12 - 12
1
32
3.4 × 3.4
12
8 - 8
3
26
The following programs require the solenoid thread wiper (OP).
13
10 - 10
1
28
36
6 - 6
0
26
27
12 - 12
1
32
37
8 - 8
0
30
14
*3
6 - 6
0
26
38
10 - 10
0
34
28
*3
8 - 8
0
30
39
12 - 12
0
38
15
*3
10 - 10
0
34
40
6 - 6
0
26
29
*3
12 - 12
0
38
41
8 - 8
0
30
16
6 - 5
1
19
42
10 - 10
0
34
3.4 × 3.4
17
8 - 7
1
23
43
*2
6 - 6
0
26
30
10 - 9
1
27
3.4 × 3.4
44
*2
10 - 10
0
34
2.4 × 3.4
*1. Check that the button hole diameter is 2mm or greater before using the programs.
*2. Do not use the button lifter spring.
*3. Thread is trimmed after sewing of one side is completed, because there is no crossover thread to be sewn.
To continue sewing to the end, keep the foot switch depressed until sewing of the other side starts, or press the foot switch
once more after sewing of the first side is completed.
