manualshive.com logo in svg

Brother HS-3000, Service Manual

The Brother HS-3000 is a versatile and advanced device that simplifies your printing tasks. With its sleek design and user-friendly interface, it offers high-quality performance. To ensure smooth operation, a (Spanish) Manual De Instrucciones is available for free download at manualshive.com, offering detailed instructions and troubleshooting guidance.

Share
Download
background image

5 - 6

Failure Investigation
for Electronic Parts

Main motor does not turn

Connect it properly.

N

Reassemble the upper shaft 
assy.

N

Y

Y

Y

Is the main motor resistance 2-5

Ω

 

at any rotation position?

Y

Y

To next page

Main motor does not turn.

Is the main motor connector correctly 
connected to the power PCB assy. (CN401)?

Is the power lead wire assy. free from 
damage and correctly connected to 
the main PCB assy. and power 
supply PCB assy.?

Replace the main motor.

N

When press the start/stop button, 
reverse stitch button and needle 
position button, does the buzzer 
sound? Is "F6" displayed?

Does the pulley turn smoothly?

Connect the power lead wire 
assy. correctly or replace it.

N

Replace the SSVR PCB assy.

N

Summary of Contents for HS-3000





































































































































































Reviews:

No comments

Related manuals for HS-3000

Fellowes Pulsar E 300 Instruction Manual preview
Pulsar E 300
Brand: Fellowes Pages: 7
Fellowes Helios 30 Instruction Manual preview
Helios 30
Brand: Fellowes Pages: 8
Fellowes Helios 60 Instructions Before Use preview
Helios 60
Brand: Fellowes Pages: 8
Kärcher B 60 W Bp Manual preview
B 60 W Bp
Brand: Kärcher Pages: 312
JUKI UnionSpecial 35800BLWG Adjusting Instructions / Illustrated Parts List preview
UnionSpecial 35800BLWG
Brand: JUKI Pages: 68
Sagitter SG ARS900C User Manual preview
SG ARS900C
Brand: Sagitter Pages: 24
Singer 157-1 Instructions For Using And Adjusting preview
157-1
Brand: Singer Pages: 10
National Flooring Equipment 14420 Instruction Manual preview
14420
Brand: National Flooring Equipment Pages: 25
Singer 117-1 Parts List preview
117-1
Brand: Singer Pages: 27
Pfaff 5483 Series Adjustment Manual preview
5483 Series
Brand: Pfaff Pages: 50
Clarke 08001B Operator'S Manual preview
08001B
Brand: Clarke Pages: 65
JUKI ASN-690 Instruction Manual preview
ASN-690
Brand: JUKI Pages: 50
JUKI DDL-9000C-S Series Instruction Manual preview
DDL-9000C-S Series
Brand: JUKI Pages: 113
Panasonic KX-PD552DL Quick Reference Manual preview
KX-PD552DL
Brand: Panasonic Pages: 4
Panasonic KX-PD715DL Quick Reference Manual preview
KX-PD715DL
Brand: Panasonic Pages: 4
Panasonic KX-PD625DL Quick Reference Manual preview
KX-PD625DL
Brand: Panasonic Pages: 4
Panasonic KX-PD525DL Quick Reference Manual preview
KX-PD525DL
Brand: Panasonic Pages: 4
Panasonic KX-PD505DL Quick Reference Manual preview
KX-PD505DL
Brand: Panasonic Pages: 4

Brands by name

Popular brands

Load more brands