Brother HL-760 Series User Manual Download Page 78

Page: 78 / 81

USER’S GUIDE

APPENDIX A –6

RESIDENT FONTS

Bitmapped Fonts

This printer has the following bitmapped fonts. They can be used in the
HP LaserJet 5P, EPSON FX-850, and IBM Proprinter XL modes. They
have the following characteristics.

•

Letter Gothic 16.66 Normal, Italic, Bold, BoldItalic (Portrait &
Landscape)

•

OCR-A(Portrait & Landscape)

•

OCR-B(Portrait & Landscape)

Scalable Fonts

The following scalable fonts can be used in the HP LaserJet 5P,
EPSON FX-850, and IBM Proprinter XL modes.

Intellifont Compatible Fonts

•

Alaska (Extrabold)

•

Antique Oakland (Oblique, Bold)

•

Brougham (Oblique, Bold, BoldOblique)

•

Cleveland Condensed

•

Connecticut

•

Guatemala Antique (Italic, Bold, BoldItalic)

•

Letter Gothic (Oblique, Bold)

•

Maryland

•

Oklahoma (Oblique, Bold, BoldOblique)

•

PC Tennessee Roman (Italic, Bold, BoldItalic)

•

PC Brussels Light (Italic, Demi, DemiItalic)

•

Utah (Oblique, Bold, BoldOblique)

•

Utah Condensed (Oblique, Bold, BoldOblique)

Microsoft Windows 3.1 TrueType Compatible Fonts

•

BR Symbol

•

Helsinki (Oblique, Bold, BoldOblique)

•

Tennessee Roman (Italic, Bold, BoldItalic)

•

W Dingbats

Summary of Contents for HL-760 Series


















































































Search results

Summary of Contents for HL-760 Series

Reviews:

Related manuals for HL-760 Series

Brands by name

Popular brands

Brother HL-760 Series, User Manual

Search results

Summary of Contents for HL-760 Series

Reviews:

Related manuals for HL-760 Series

Brands by name

Popular brands