manualshive.com logo in svg

Brother HL-5580D, Service Manual

The Brother HL-5580D Service Manual is an essential resource for troubleshooting and maintaining your printer. Our website offers a comprehensive manual for download, completely free of charge. Ensure optimal performance and extend the lifespan of your printer with this indispensable manual. Download it now from manualshive.com.

Share
Download
background image

2-71

Confidential

Error code 8501

When printing from paper tray 1 to 5, the T1 paper feed sensor detected open paper tray 1 
(before registering printing data to engine).

Error code 8502

When printing from paper tray 2 to 5, the T2(LT or TT) paper feed sensor detected open 
paper tray 2 (before registering printing data to engine).

Error code 8503

When printing from paper tray 3 to 5, the T3(LT or TT) paper feed sensor detected open 
paper tray 3 (before registering printing data to engine).

Error code 8504

When printing from paper tray 4 to 5, the T4(LT or TT) paper feed sensor detected open 
paper tray 4 (before registering printing data to engine).

<User Check>

• Close the appropriate paper tray correctly.

Step

Cause

Remedy

1

Malfunction of an LT control 
PCB or TT control PCB

Install the latest main firmware.

2

An LT/TT paper feed actuator 
coming off or caught in some 
sections of the machine

Reattach the appropriate LT/TT paper feed 
actuator.

3

An LT/TT paper feed sensor 
failure

Replace the appropriate LT/TT paper feed 
sensor PCB ASSY.

4

High-voltage power supply PCB 
failure

Replace the high-voltage power supply PCB 
ASSY.

5

An LT control PCB failure

Replace the appropriate LT control PCB ASSY.

6

TT relay PCB failure

Replace a TT relay PCB ASSY.

7

TT control PCB failure

Replace the TT control PCB ASSY.

8

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HL-5580D

Dascom TALLY MIP480 User Manual preview
TALLY MIP480
Brand: Dascom Pages: 138
Dascom T2150 User Manual preview
T2150
Brand: Dascom Pages: 166
Pantum M9106 Series User Manual preview
M9106 Series
Brand: Pantum Pages: 164
Canon PIXMA iP4910 Getting Started preview
PIXMA iP4910
Brand: Canon Pages: 4
QuickLabel Systems QL800 User Manual preview
QL800
Brand: QuickLabel Systems Pages: 122
Lexmark 34A0252 Troubleshooting Manual preview
34A0252
Brand: Lexmark Pages: 9
Printek DP-530si Operator'S Manual preview
DP-530si
Brand: Printek Pages: 34
Lexmark Color Jetprinter 810 Series Quick Install preview
Color Jetprinter 810 Series
Brand: Lexmark Pages: 2
Oki LE810DTUPS Safety Information Manual preview
LE810DTUPS
Brand: Oki Pages: 20
Tascam P11/TAS Technical Documentation preview
P11/TAS
Brand: Tascam Pages: 2
Kyocera Mita 1900N - B/W Laser Printer Operation Manual preview
1900N - B/W Laser Printer
Brand: Kyocera Mita Pages: 286
Kodak ESP Office 6100 Series Extended User Manual preview
ESP Office 6100 Series
Brand: Kodak Pages: 94
Weber Markoprint X4JET Manual For Installation, Operation And Maintenance preview
Markoprint X4JET
Brand: Weber Pages: 177
3nStar RPT008 Programmer'S Manual preview
RPT008
Brand: 3nStar Pages: 44
BT PaperJet 65E User Manual preview
PaperJet 65E
Brand: BT Pages: 64
Xprinter XP-425B Series User Manual preview
XP-425B Series
Brand: Xprinter Pages: 40
GALLERY 1390R User Manual preview
1390R
Brand: GALLERY Pages: 10
Brother DCP-J925DW Service Manual preview
DCP-J925DW
Brand: Brother Pages: 378

Brands by name

Popular brands

Load more brands