Brother HL-2260 Manual Download Page 10

vii

Confidential

Disconnect Device

Wiring Information (U.K. only)

If you need to replace the plug fuse, fit a fuse that is approved by ASTA to BS1362 with the 
same rating as the original fuse.

Always replace the fuse cover. Never use a plug that does not have a cover. If in any doubt, 
call a qualified electrician.

Warning -This product must be earthed.

The wires in the mains lead are coloured in line with the following code:

• Green and Yellow: Earth

• Blue: Neutral

• Brown:  Live

LAN Connection (Network models only)

Radio Interference

This product complies with EN55022 (CISPR Publication 22)/Class B.

Recycling Information in accordance with the WEEE and Battery Directives

The product/battery is marked with one of the above recycling symbols. It indicates that at 
the end of the life of the product/battery, you should dispose of it separately at an appropriate 
collection point and not place it in the normal domestic waste stream.

 

CAUTION

This product must be installed near an electrical socket that is easily accessible. In case of 
emergencies, you must disconnect the power cord from the electrical socket to shut off 
power completely.

 

CAUTION

DO NOT connect this product to a LAN connection that is subject to over-voltages.

Product mark

Battery mark

European Union only

Summary of Contents for HL-2260





















Reviews: