manualshive.com logo in svg

Brother FAX-2950, Basic User'S Manual

Share
Download
Brother FAX-2950 Basic User'S Manual Download Page 88

80

Init Unable XX

(XX = Error Code)

The machine has a mechanical 
problem.

(For FAX-2840 and MFC-7240) 

Received fax messages still in memory 
will be lost when the machine is turned 
off. See 

Transferring your faxes or Fax 

Journal report

 

uu

 page 83 before 

disconnecting the machine so you will 
not lose any important messages. Then, 
turn the power switch off, wait a few 
seconds, and then turn it on again. 
Leave the machine for 15 minutes with 
the power on.

(For FAX-2950 and MFC-7290) 

Turn the power switch off, wait a few 
seconds, and then turn it on again. 
Leave the machine for 15 minutes with 
the power on.

If the problem continues, call  Brother 
Customer Service or your local Brother 
dealer.

Jam Inside

The paper is jammed inside the 
machine.

(See 

Paper is jammed inside the machine

 

uu

 page 88.)

Jam Rear

The paper is jammed in the back 
of the machine.

(See 

Paper is jammed at the back of the 

machine

 

uu

 page 85.)

Jam Tray

The paper is jammed in the paper 
tray of the machine.

(See 

Paper is jammed in the standard paper 

tray

 

uu

 page 84.)

Manual Feed

Manual

 was selected as the 

paper source when there was no 
paper in the manual feed slot.

Place a sheet of paper in the manual feed 
slot. (See 

Loading paper in the manual feed 

slot

 

uu

 page 12.)

No Paper

The machine is out of paper or 
paper is not correctly loaded in 
the paper tray.

Do one of the following:

Refill the paper in the paper tray and 
press 

Start

.

Remove the paper and load it again. 
Then press 

Start

.

If the problem is not resolved, the paper 
pick-up roller may need to be cleaned. 
Clean the paper pick-up roller. (See 

Cleaning the paper pick-up rollers

 

uu

 page 74.)

No Response/Busy

The number you dialled does not 
answer or is busy.

Verify the number and try again.

No Toner

The toner cartridge is not installed 
correctly.

Pull out the drum unit. Take out the toner 
cartridge and then put it back into the drum 
unit.

Error Message

Cause

Action

Summary of Contents for FAX-2950

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands