manualshive.com logo in svg

Brother DCP Series, Service Manual

The Brother DCP Series offers advanced multifunctional printers that simplify everyday tasks. Whether you need to print, copy, or scan, our user-friendly devices provide exceptional performance. At manualshive.com, you can easily access the comprehensive user manuals for your Brother DCP Series printer, available for free download.

Share
Download
background image

3-90

Confidential

9.26 Registration Sensor PCB ASSY

(1) Remove the four screws of the TAPTITE CUP B M3x10 and remove the Side frame L. 

Assembling Note  

Attach the Side frame L under the Earth plate.

(2) Remove the Registration sensor harness wiring.

(3) Remove the screws of the TAPTITE CUP B M2.6x8, and remove the Registration

sensor PCB ASSY.

(3_072L)

TAPTITE CUP B M3x10

Side frame L

Earth plate

Side frame L

(3_073L)

Registration sensor PCB ASSY

TAPTITE BIND B M2.6x8

Registration sensor harness

Summary of Contents for DCP Series






















































































































































































































































































































Reviews:

No comments

Related manuals for DCP Series

Oki MC560 MFP CX2032 Guia Do Usuário preview
MC560 MFP CX2032
Brand: Oki Pages: 247
Printekmobile FieldPro 530 Quick Start Manual preview
FieldPro 530
Brand: Printekmobile Pages: 2
Riso MZ1070 Technical Manual preview
MZ1070
Brand: Riso Pages: 150
TEC B-570 SERIES Maintenance Manual preview
B-570 SERIES
Brand: TEC Pages: 92
Xerox Nuvera 100 roduction Systems Paper Manual preview
Nuvera 100 roduction Systems
Brand: Xerox Pages: 70
Output Technology LaserMatrix LM2405 Operator'S Manual preview
LaserMatrix LM2405
Brand: Output Technology Pages: 249
Epson C11C418001 - Stylus C60 Inkjet Printer Printer Basics Manual preview
C11C418001 - Stylus C60 Inkjet Printer
Brand: Epson Pages: 64
Epson C11C417001 - Stylus Photo 820 Color Inkjet Printer Start Here preview
C11C417001 - Stylus Photo 820 Color Inkjet Printer
Brand: Epson Pages: 2
Epson C11C417001 - Stylus Photo 820 Color Inkjet Printer Specifications preview
C11C417001 - Stylus Photo 820 Color Inkjet Printer
Brand: Epson Pages: 2
Epson C11C294131BZ - LX 300+ B/W Dot-matrix Printer User Manual preview
C11C294131BZ - LX 300+ B/W Dot-matrix Printer
Brand: Epson Pages: 100
Epson C117001-N - DFX 5000+ B/W Dot-matrix Printer Service Manual preview
C117001-N - DFX 5000+ B/W Dot-matrix Printer
Brand: Epson Pages: 186
Oki C9600hdn Troubleshooting Manual preview
C9600hdn
Brand: Oki Pages: 15
Epson C11C498001 - Stylus Photo 825 Inkjet Printer Brochure & Specs preview
C11C498001 - Stylus Photo 825 Inkjet Printer
Brand: Epson Pages: 2
Xerox Phaser 3600 Instruction preview
Phaser 3600
Brand: Xerox Pages: 23
Avery Dennison AP4.4_5.4 Manual preview
AP4.4_5.4
Brand: Avery Dennison Pages: 92
FARGO electronics Color ID Card Printer II Operating Instructions Manual preview
Color ID Card Printer II
Brand: FARGO electronics Pages: 70
MyBinding Afinia Label L701 Instruction Manual preview
Afinia Label L701
Brand: MyBinding Pages: 85
Canon MP21DV Instructions preview
MP21DV
Brand: Canon Pages: 4

Brands by name

Popular brands

Load more brands