manualshive.com logo in svg

Brother B-500, Service Manual

Share
Download
Brother B-500 Service Manual Download Page 165

5 - 3

Electronic Parts

Failure Investigation for Electronic Parts Power does not come on

When the power is turned ON, the 
buzzer does not sound

Replace the inlet assy.

or

Replace the power supply code

With the power cord plugged into an outlet, 
is the voltage between pins 1 & 2 on the 
inlet assy. connector 120 (220 – 240) V AC?

Are the voltages between pins 2 & 3 and 
pins 3 & 4 of CN5 on the main PCB assy. 
normal?
• Pins 2 – 3 ...   5 V DC
• Pins 3 – 4 ... 30 V DC

N

N

Replace the SS-VR PCB assy.

Does the buzzer sound when the power 
is turned ON with the SS-VR PCB assy. 
connector disconnected from the main 
PCB assy.?

Y

Reconnect the connector of 
the PW SW assy. to CN101 of 
the power supply PCB assy.

or

Replace the PW SW assy.

Reconnect the connector of the 
power lead wire to CN201 of the 
power supply PCB assy. and to 
CN5 of the main PCB aasy.

or

Replace the power supply 
PCB assy.

N

N

Replace the operation PCB 
assy.

Does the buzzer sound when the power 
is turned ON with the operation PCB 
assy. connctor disconnected from the 
main PCB assy.?

Y

N

Y

Is the voltage between pins 1 & 2 of 
CN101 on the power supply PCB assy. 
120 (220 – 240) V AC?

Y

Y

Replace the main PCB assy.

Summary of Contents for B-500




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands