manualshive.com logo in svg

Brother 9045CDN - DCP Color Laser, User Manual

Share
Download
Brother 9045CDN - DCP Color Laser User Manual Download Page 122

108

Cleaning the drum unit

C

If you have the following print quality 
problems, clean the drum unit as follows.

a

Press the front cover release button and 
then open the front cover.

 

b

Close the front cover of the machine. 
The machine starts warming up, wait 
until it finishes warming up before going 
on to step

c

.

c

Pull out the MP tray (1) and unfold the 
MP tray support flap (2).

 

d

Put a blank sheet of A4 or Letter sized 
paper in the MP tray.

 

e

While pressing and holding down 

Clear/Back

 press

d

 until 

DRUM CLEANING

 is displayed on the 

LCD.

 

f

Press 

Black Start

 or 

Color Start

. The 

paper will feed into the machine to start 
the drum cleaning. 

 

 

ABCDEFGHIJKLMNOPQRSTUVWXYZ. 0123456789. abcdefghijklmnopqrstuvwxyz.
ABCDEFGHIJKLMNOPQRSTUVWXYZ. 0123456789. abcdefghijklmnopqrstuvwxyz.
ABCDEFGHIJKLMNOPQRSTUVWXYZ. 0123456789. abcdefghijklmnopqrstuvwxyz.
ABCDEFGHIJKLMNOPQRSTUVWXYZ. 0123456789. abcdefghijklmnopqrstuvwxyz.

ABCDEFGHIJKLMNOPQRSTUVWXYZ. 0123456789. abcdefghijklmnopqrstuvwxyz.
ABCDEFGHIJKLMNOPQRSTUVWXYZ. 0123456789. abcdefghijklmnopqrstuvwxyz.
ABCDEFGHIJKLMNOPQRSTUVWXYZ. 0123456789. abcdefghijklmnopqrstuvwxyz.
ABCDEFGHIJKLMNOPQRSTUVWXYZ. 0123456789. abcdefghijklmnopqrstuvwxyz.

75 mm / 2.95 in.

75 mm / 2.95 in.

1

2

Summary of Contents for 9045CDN - DCP Color Laser

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands