background image

13

If your home has specially wired alarm equipment connected to the telephone line, ensure the 
installation of this equipment does not disable your alarm equipment. If you have questions about 
what will disable alarm equipment, call your telephone company or a qualified installer.

If you are not able to solve a problem with your product, call Brother Customer Service. (See 

Brother numbers

 in the 

Basic User's Guide

.)

WARNING

 

For protection against the risk of electrical shock, always disconnect all cables from the wall 
outlet before servicing, modifying or installing the equipment.

 

Federal Communications Commission (FCC) Declaration of 
Conformity (USA only)

A

declares, that the products

Product Name: 
HL-4150CDN/HL-4570CDW/HL-4570CDWT/MFC-9460CDN/MFC-9560CDW/MFC-9970CDW

Model Numbers: HL-41/HL-45/MFC-9460CDN/MFC-9560CDW/MFC-9970CDW

Product Options: LT-300CL

comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by one or more of the following 
measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.

Call the dealer or an experienced radio/TV technician for help.

Responsible Party:

Brother International Corporation
100 Somerset Corporate Boulevard
Bridgewater, NJ 08807-0911 USA
TEL: (908) 704-1700

Summary of Contents for 4570CDW





















Reviews: