Brooks CTI-Cryogenics Installation, Operation And Maintenance Instructions Download

Page: 19 / 82

High Capacity Helium Compressor

Introduction

Manual Specifications

Brooks Automation

8040600

Revision A

1-9

Figure 1-6: Cooling Water Flow versus Inlet Temperature

(Three Compressor Modules High Voltage Configuration)

General

The information in

Table 1-3

provides general High Capacity Helium

Compressor operating specifications.

Table 1-3: General High Capacity Helium Compressor Operating Specifications

Specification

Low Voltage

High Voltage

Part Number

8128908G001 - 3 modules
8128904G003 - 2 modules
8128903G003 - 3 modules

8128908G002 - 3 modules
8128904G004 - 2 modules
8128903G004 - 3 modules

Input Power Cable

(

Check local electrical

codes

3 conductor cable with ground
Rated 600 VAC
Check local electrical codes

Helium Static Pressure

325 - 335 psig
(22.4 - 23.1 bars)

Ambient

Operating Temperature

Range

50 - 100º F
(10 - 38º C)

High Capacity (High Voltage) Compressor Cooling Water Flow Rate vs Inlet Temperature

60 Hz Operation, 3 compressor unit

3.00

4.00

5.00

6.00

7.00

8.00

9.00

10.00

Cooling Water Inlet Temperature, degrees F

nde

d Minim

Flow R

, gpm

342-355 VAC 60 Hz

355-365 VAC 60 Hz

365-375 VAC 60 Hz

375-506 VAC 60 Hz

Summary of Contents for CTI-Cryogenics



















































































Search results

Summary of Contents for CTI-Cryogenics

Reviews:

Related manuals for CTI-Cryogenics

Brands by name

Popular brands

Brooks CTI-Cryogenics, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for CTI-Cryogenics

Reviews:

Related manuals for CTI-Cryogenics

Brands by name

Popular brands