23
1
GENERAL WARNINGS
The installation of the thermo-stove must be done according to the local, national or European regulations.
Thermo-stoves by Bronpi Calefacción, S.L. are manufactured under a quality control system in order to protect both the user and the fitter
in the event of possible accidents. We also recommend to the authorized personnel that, each time that an operation in the thermo-stove is
going to be done, pay special attention to the electrical connections, especially that stripped or bear wires which should never be outside the
connections, avoiding dangerous contacts.
The installation must be performed by authorized personnel who must provide the buyer a declaration of conformity of the
installation where he will assume full responsibility for the final installation and, therefore, the proper operation of the installed
product. Bronpi Calefacción S.L. will not assume any liability in the case of failure to comply with these precautions.
The manufacturer will not assume any liability for damages caused to third parties due to improper installation or misuse of the thermo-stove.
In order to ensure the correct operation of the product, components can only be replaced with original spare parts and by an authorized
technician.
Maintenance of the stove must be performed at least once a year by an Authorized Technical Service.
For your safety and security you should consider:
•
Do not touch the thermo-stove with bare feet or with wet body parts.
•
The door of the machine must be closed during operation.
•
It is forbidden to modify the safety or regulating devices without the permission of the manufacturer.
•
Avoid direct contact with any parts of the product that tend to reach high temperatures during its operation.
2
GENERAL DESCRIPTION
The thermo-stove that you have purchased contains the following pieces:
•
Complete structure of the thermo-stove on the pallet.
•
Inside the combustion chamber you can find: a box/bag with a thermal glove that allows us to use the handle of the door and other
components. The electrical interconnection cable between the thermo-stove and the electrical network. A hook (cold hands handle) to
make easier the removing and cleaning of the burner. The remote control of the thermo-stove (battery included). A yellow leaflet with
the most important warnings and considerations. A book in order to register all maintenance tasks performed to the thermo-stove as
well as this installation, use and servicing manual.
•
Inside the combustion chamber you will also find the burner and the ash pan.
The equipment consists of several elements of steel sheets welded, with different thickness and, depending on the model, pieces of cast iron.
It also has a door with vitro ceramic glass (resistant up to 750ºC) and ceramic rope seal for the air tightness of the combustion chamber.
The heating of the surrounding ambient is produced by
radiation:
through the glass-ceramic and the body, the heat is radiated into the room.
Model Omega-H, due to the thermal insulation that it has, this radiation is of low calorific value, so its performance and the power transferred
to water are greatly increased. Heat is also radiated through the hydraulic circuit in which it is installed (radiators, panels, under floor heating,
etc) because the thermo-stove reaches a high thermal efficiency derived from a large exchange surface and water capacity, which is
generated by a chamber that completely surrounds (side, top and bottom) the combustion chamber.
3 FUELS
WARNING:
The use of a low quality pellet or any other fuel in disagreement with the specifications mentioned below implies the cancellation of
the warranty and the responsibility bounded to the product
Only wood pellets certified by these rules should be used:
•
Ö-Norm M 7135
•
DIN plus 51731
•
UNI CEN/TS 14961
•
EN+ 14962-2
Bronpi Calefacción recommends the use of pellets with 6 mm diameter, a maximum longer of 3.5 cm and with a humidity percentage lower
than 8%.
•
STORAGE OF PELLET
In order to guarantee combustion without any problem it is necessary to keep the pellet in a dry ambient.
•
PELLET SUPPLY
Open the tank cover on the top of the equipment and empty directly the pellet bag taking care of not overflowing.
4
SAFETY DEVICES
•
SMOKE EXTRACTOR FAN BREAKDOWN
If the extractor fan stops, the electronic card automatically blocks the fuel supply.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS
HYDRO SERIES
EN
Summary of Contents for Dama Hydro
Page 107: ...106 12 1 DAMA H FT ...
Page 109: ...108 12 2 LETICIA H FT ...
Page 111: ...110 12 3 REYNA H FT ...
