Brocade Communications Systems ICX 6650 series Hardware Installation Manual Download Page 40 | Manualshive

Page: 40 / 83

background image

7. Insert the earth ground wire into the ground terminal on the DC wiring assembly.

NOTE

This equipment installation must meet NEC/CEC Code requirements. Consult local authorities for regulations.

8. Insert the DC power supply wiring assembly with the wires connected into the power supply and tighten the assembly screws.
9. Using the handle on the power supply, hold the power supply level and guide it into the carrier rails on each side of the power

supply slot. Gently push the power supply all the way into the slot, ensuring that it firmly engages with the connector.

FIGURE 22

Installing a DC power supply unit

10. When you are sure the power supply has properly engaged the connector, tighten the chassis attachment screws to secure the

power supply in the slot.

When the device is powered on, the power LED on the device should turn green to confirm that the power supply is correctly installed
and supplying power.

CAUTION
If you do not install a module or a power supply in a slot, you must keep the slot filler panel in place. If you run the chassis
with an uncovered slot, the system will overheat.

Installing an SFP+ transceiver

To monitor the transceivers, the

show media

command output shows the transceiver information for all interfaces on the switch. Third-

party transceivers are allowed. Brocade provides support for third-party transceivers, but may require a Brocade transceiver be used for
troubleshooting.

Support will not be provided if there is an issue with the third-party transceiver.

Complete the following steps to install an SFP+ transceiver.

1. Remove any protector plugs from the transceivers and the ports.
2. Making sure that the bail (wire handle) is in the unlocked position, place the SFP+ transceiver in the correctly oriented position on

the port.

NOTE

The QSFP+ 40 GbE LR4 optical transceiver is supported in ports 1 and 2 only. When the module is inserted into a
stack-unit/slot number/port number combination that is not 1/2/1 or 1/2/2, the following error message displays:
“QSFP LR-4 optics not supported on port

port-number

.”

Installing an SFP+ transceiver

Brocade ICX 6650 Hardware Installation Guide

40

Part Number: 53-1003621-04

«
...
38
39
40
41
42
...
»

Summary of Contents for ICX 6650 series




















































































Reviews:

No comments

Related manuals for ICX 6650 series

All in One Printer

Brand: Baracoda Pages: 42

Adapter Bracket

Brand: Paradyne Pages: 1

Brand: Dahua Pages: 6

Brand: Axis Pages: 104

Brand: Ruckus Wireless Pages: 102

Brand: IBM Pages: 32

JetWeb JX2-PR0FI1

Brand: Jetter Pages: 67

Brand: Allied Telesis Pages: 1

Brand: Paradyne Pages: 23

Vigor 2760 Series

Brand: Draytek Pages: 54

Brand: H3C Pages: 103

Brand: FiberHome Pages: 44

Brand: Allied Telesis Pages: 128

P-660R-F1 series

Brand: ZyXEL Communications Pages: 268

Brand: Allied Telesis Pages: 44

Compressor DW-CP04

Brand: Digital Watchdog Pages: 73

Brand: Planet Pages: 67

Brand: Hitachi Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands