background image

4

3. BUILD FRAMEWORK

HD1151A

F

RAMING

 

BEHIND

 

DRYWALL

W

ALL

 

STUDS

34 ¾”  = 

BOTTOM

 

OF

 

HOOD

 24” 

ABOVE

 

COOKTOP

40 ¾”  = 

BOTTOM

 

OF

 

HOOD

 30” 

ABOVE

 

COOKTOP

    WARNING

!

•  When cutting or drilling into wall, do not damage electrical wiring and other hidden utilities.
•  When building framework, always follow all applicable construction codes and standards.

Construct wood wall framing that is even with the surface of wall studs.
Wood wall framing must be at least 1/2” thick and 3” high. Fasten wood wall 
framing to wall studs for a solid installation.
Make sure that the height of the framing will allow the retaining screws to be 
secured to the framing within the dimensions shown.

After wall surface is finished

, using a level, draw a vertical line up to the 

ceiling starting from the center of the planned hood location. Measure and 
mark the retaining screw locations using the measurements given in illustration 
at right. Insert 2 M4 x 38 Phillips 9 mm round head mounting screws in wall 
framing; do not completely tighten the screws at this time.

4.  INSTALL UPPER FLUE MOUNTING BRACKET (

DUCTED

 

INSTALLATION

 

ONLY

)

Center the upper flue mounting bracket with the center line previously 
drawn in step 3 and place it flush with the ceiling. Use the upper flue 
mounting bracket as a template to mark the position of its screws.

Secure the upper flue mounting bracket to the wall using 2

 

M4 x 38 

Phillips 9 mm round head mounting screws. Make sure that the bracket 
is tight against the wall.

5.  INSTALL PLENUM (

NON

-

DUCTED

 

INSTALLATION

 

ONLY

)

Center the plenum with the center line previously drawn in step 3 and 
place it flush with the ceiling. Use the plenum mounting slots as a 
template to mark the position of its screws.

Secure the plenum to the wall using 2

 

M4 x 38 Phillips 9 mm round 

head mounting screws. Make sure that the plenum is tight against the 
wall.

C

L

HD1150

C

ENTER

 

OF

 

INSTALLATION

U

PPER

 

FLUE

 

MOUNTING

 

BRACKET

 

SLOTS

M

OUNTING

 

BRACKET

 

FLUSH

 

WITH

 

CEILING

C

EILING

L

C

 

HD1158

C

EILING

P

LENUM

 

FLUSH

 

WITH

 

CEILING

C

ENTER

 

OF

 

INSTALLATION

P

LENUM

 

MOUNTING

 

SLOTS

Summary of Contents for EW48 Series













Reviews: