background image

Broadcom

- 9 -

SAS 9305-16i PCI Express to 12Gb/s SAS Host Bus Adapter User Guide
June 17, 2016

Chapter 1: SAS 9305-16i Host Bus Adapter User Guide

Replacing the Bracket

Ports 0-7 can be configured as eight separate ports or combined into one or more groups called wide ports (one  x4, 
two x4s, one x8, and so on.). Similarly, ports 8-15 can be configured as eight separate ports or combined into one or 
more wide ports. A single wide port cannot combine individual ports or PHYs sourced by different SAS cores.

When configuring a boot-device in a multi-path environment, the target must be connected to one or more ports on 
the same SAS core with 

AutoPortConfig

 enabled. The boot device appears to the host system as a single device on the 

active path. A different controller is managed by the multi-path environment as the passive path.

When configuring data-storage devices in a multi-path environment, the rule for creating wide ports applies, but 
multiple ports from different SAS cores can be connected to the data-storage devices. The multi-path environment 
manages data-storage devices that are presented by the controller more than once.

1.9

Replacing the Bracket

To replace the bracket for the Avago 12Gb/s SAS HBA, follow these steps:

1.

At an ESD-safe workstation, remove the board from its ESD protective bag.

ATTENTION

Never apply pressure to the bracket or the heat sink when inserting 
the board. Do not handle the board by the bracket. Do not handle the 
heat sink at any time. Do not bend or twist the board at any time.

2.

Use an ESD-safe #1 Phillips screwdriver to carefully remove the two Phillips screws that connect the bracket to the 
board. The following figure shows how to unscrew the two screws located at the top edge and bottom edge of the 
board.

CAUTION

Damaging the screw can void the warranty. To prevent damage to the 
screw, make sure that the screwdriver is centered in the top of the 
screw.

Figure 3  Removing the Bracket Screws

Table 2  Board Port to SAS Core Association 

Board Ports

Ports 0-3

Ports 4-7

Ports 8-11

Ports 12-15

SAS Core Instance

SAS Core 0

SAS Core 0

SAS Core 2

SAS Core 2

Summary of Contents for SAS 9305-16i













Reviews: