background image

Broadcom Ltd.

- 7 -

Broadcom 9305-16e PCI Express to 12Gb/s SAS Host Bus Adapter User Guide
January 27,  2016

12Gb/s SAS HBA Certifications and Safety Characteristics

Relative humidity range: 5 percent to 90 percent noncondensing

6

12Gb/s SAS HBA Certifications and Safety Characteristics

All Broadcom 12Gb/s SAS HBAs meet or exceed the requirements of UL flammability rating 94V-0. Each bare board is 
marked with the supplier’s name or trademark, type, and UL flammability rating. Because these boards are installed in 
a PCIe bus slot, all voltages are less than the SELV 42.4-V limit.

The design and implementation of the 12Gb/s SAS HBA minimizes electromagnetic emissions, susceptibility to radio 
frequency energy, and the effects of electrostatic discharge.

The 12Gb/s SAS HBA meets the following integrated electromagnetic interference (EMI) compliance labels:

CE mark

RCM mark

Canadian Compliance Statement

FCC Class B, marked with the FCC Self-Certification logo

UL Listed Mark for Canada/U.S.

Japan VCCI

Korean KCC

Taiwan BSMI

The 12Gb/s SAS HBA meets the following environmental directives:

Restriction of Hazardous Substances (RoHS)

Waste of electrical and electronic equipment (WEEE)

7

Hardware Installation Instructions

To install the Broadcom 12Gb/s Serial Attached SCSI (SAS) HBA, follow these steps:

1.

Unpack the HBA, and inspect it for damage.

 Unpack the HBA in a static-free environment. Remove the HBA from 

the anti-static bag, and carefully inspect the device for damage. If you notice any damage, contact Broadcom or 
your reseller support representative.

ATTENTION

To avoid the risk of data loss, back up your data before you change 
your system configuration.

2.

Prepare the computer.

 Turn off the computer, and disconnect the power cord from the rear of the power supply.

CAUTION

Disconnect the computer from the power supply and from any 
networks to which you will install the HBA, or you risk damaging the 
system or experiencing electrical shock.

3.

Remove the cover from the chassis.

Summary of Contents for SAS 9305-16e











Reviews: